WC301 Maytag Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
would not drain
The part was a bit difficult to put on and then I discovered that it still would not drain. It turned out that my drain hose was plugged
Parts Used:
-
Donald from Lake City, MN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Faucet adapter leaked
-
Ed from North East, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
water leak - tub overflow
remove panel on front to acess float @ float switch.Remove phillips screw to float switch,remove palnut from float shaft with 5/16 nutdriver.Remove float from inside washer.Reinstall new parts reverse order.
Parts Used:
-
walter from salisbury, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Belt to stiff to roll onto pulley
150 degrees for ten minutes provided enough flexibility to allow the belt to be rolled around the pulley. The machine has been used successfully since installation.
Parts Used:
-
John from Los Alamos, NM
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Broken Belt
After discovering the broken belt. 2 Days later I had the new belt from partselect. I placed the belt on the motor pulley then after 3-4 attempts was able to get the belt on the other pulley. It will go on. Comments from other customers really helped. After you get belt on then apply lub, per instructions. My maytag is over 20 years old still works great.
Parts Used:
-
WILLIAM from CONNEAUT, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would pump the used water out.
Changed float switch to no avail! Ladeled out the water. Disassembled the entire pump unit inside down to the motor shaft and checked all pieces for trouble. Could find nothing wrong. Now trying to determine if the problem is in the timer or motor.
Parts Used:
-
Robert from Bandon, OR
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
leaking water
replaced gasket.Didn't fix leaking water problem.I believed that there was too much water in washer, when the problem occurred.Found that the float had soap build up in it making it too heavy,letting in more water than the washer can handle.Cleaned build up from float and problem seems to have disappeared.
Parts Used:
-
Noel from Temperance, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Motor running but no motion or pumping action
Removed the kick plates to access the pulley system, Heated the clear belt in hot water and installed it by rotating the large pulley to stretch the belt on. Then added the lubricant to the belt. Reinstalled the kick plates with nut driver.
Parts Used:
-
John from Slidell, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
changed out kitchen sink faucet set
replaced the faucet adapter I did not save when I change out the kitchen sink faucet set
Parts Used:
-
George from Cameron, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Nipple that upper spray arm goes on.
Maytag dealer said the part was unavailable but there I sat looking at it.
Parts Used:
-
Roger from Saganaw, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!