VCD321D*C18 General Electric Dryer - Instructions

Based on the symptom (drum not turning), I figured that the belt was shot. I found a video on YouTube that described how to fix it. I also found directions here on this site on how to fix it! Here's what I did: step1: there were two screws holding the top on. took them off and the top swung up, exposing the drum and broken belt. step2: took off the two screws holding the front on. tipped the front forward so I could get the new belt around the drum. step 3: took the back plate off (10 screws). had to remove the exhaust tube first. cleaned out all the lint with the shop vac. there was plenty of lint everywhere. step 4: put the belt onto the motor pulley wrapping around the tension pulley. step5: put everything back together and plugged it in. everything worked fine. it took longer to vacuum all the lint out than it did for the actual repair.

Had to tap three holes in the rear bearing to match the three attachment screws. Screw up with the part.

disassembled chassis of dryer, unbolted top, lifted top to expose drum. bolted top back on. resumed repair next morning. unbolted top. lifted drum (it moved up and down about 1 inch) and got new belt around it. rebolted top down. tipped dryer to its back. unbolted and removed panel at bottom, exposing drive motor and tensioner spring. positioned belt around drive motor spindle and tensioner spring. replaced panel. reconnected dryer to electricity. reconnected gas using new flexible connector.

I did not have an actual repair. I simply replaced the lint filter that dropped into the receptacle. However, what I want to mention is that the part was available as old as the dryer is and there was a nice photo to scale of the replacement part so that I was sure I was getting the correct piece. A great site to obtain parts from my experience.

Just replaced it with the new one

I only ordered a lint filter with frame but wanted to let other's know that ordering from your site was extremely easy and the shipping was extremely fast!! I received my order with 2 days of placing my order. Thank you!!

After having a friend who repairs appliances come and diagnose the problem, I was able to find the parts I needed very easily at PartSelect. They came quickly and I removed the front panel, followed the instructions (they were not very detailed) and also had help reading some of the other posts from people on the website. I replaced the parts and the dryer is now quiet and running fine.

inserted the latch into the opening in the front face of the dryer

Removed two screws from front by door. Removed back panel to remove belt from tensioner. lifted lid of dryer. removed two more screws from inside to remove front panel. while holding the barrel I removed the front panel then grabbed barrel and pulled out. took off the old bearing, put the new one on and reassembled it the way I took it apart. The whole thing took about 10 min was quick and easy if there is any problems while you are doing it look it up on youtube.com and you can see it done.

Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.

no instructions necessary for this part install

place new filter in

Remove the Torx screws along the front top edge and flipped the top back. Removed two screws at the top inside holding the front panel on. Loosened two screws at the front bottom and took the front panel off. Pulled the drum out the front. I gave everything a good vacuuming with a shop vac and a long handle brush. Then went around back, removed the access panel, removed the rear drum bearing plate and installed the new one. Removed the rear bearing from the back of the drum and installed the new one (You have to work from both sides of the drum which makes it a little tricky.I used a couple of wire ties to hold everything in place while I lined everything up. Screws or punches would work too). The front drum slides are held in by 2 screws each and you could replace them without removing the drum. They need to be lubed with the lubricant supplied. I put the drum partially in then looped the belt over the narrow back part of the drum, around the motor pulley and idler pulley. Put the drum all the way in and the belt onto the drum by rotating it by hand. The belt ribs go against the drum. Installing the belt was the a little tricky but not impossible. It could be easier if you loosen the left side panel to give you some room to reach in but I was able to do it without doing that. Threw the front and top back on and was done. Total time was about 1.5 hours a lot of which was spent getting the dryer in and out of the little cubby hole it lives it.

The ordering and receiving of the part were wonderfully easy, but the construction of the lint filter left a lot to be desired. Bits of wire extended past the edge of the frame and drew blood when held, so had to trim the wire screen that extended past the frame. Also, the wire screen was not attached continuously around the frame and had to be clamped and glued. I did appreciate that the filter fit my machine.

I removed the top of the dryer and verified the broken belt. Since the dryer is almost 20 years old, I decided to go a little further just to make sure that was all that was wrong. After I removed the drum I found the rear drum bearing worn. The parts were here in a couple days!Replacing the parts took about an hour. Getting the drum to line up with the three mounting holes was the hardest. I took three machine screws the same pitch but longer, cut the heads off them and used them as alignment pins. Now my dryer is quieter than it has been in years, all for less than 20 dollars including shipping!!