TFX22XPDAWW General Electric Refrigerator - Instructions

Disconect and Removed cover from back of frig.
Removed water supply pipe (adjustable wrench).
Removed Bracket and Valve Assembly from frig (1 screw).
Marked tube placements with marker so that I could put them back correctly.
Removed power connectors from valve.
Disconected tubes from valve (not that easy to pull off).
Connect tubes on new valve. Plug power connectors back in.
Screw the Assembly back on the frig.
Reconnect water supply & test for leaks.

Bing , Bang, Boom.

as simple as taking off 4 screws from door of old one and putting door on new one and putting bucket back in place

I carefully removed the screws and laid aside in order. Taking off the ice grinders was the trickiest part, but I had read before to make sure to keep them in order. Replaced two new parts and reassembled. Pretty simple, but just keep track of where each part goes.

Unfortunately, the replacement part didn't come with instructions. The repair, nevertheless, was fairly straightforward. After removing the plastic parts that guide the ice through the door (by removing a few screws that attach the parts to the inside of the door), I was able to slip my hand into the ice maker dispenser and remove the old part. The part clips on. It is a tight fit through the funnel (from the outside of the freezer), however, and requires that the gasket first be "flipped" open wherein it unfolds 180 degrees. Doing this will make it easier to clip the new gasket onto the assembly.

The replacement part was an exact fit and slipped right into the space where the old one was. No tools needed.

Removed old sheild and reached in freezer replacing sheild with screwdriver. 3 - 4 minutes.
Ordered sheild online one afternoon and received the nest afternoon. Great transaction. will use again when needed.

George in Louisville, KY

Turn off water to the refrigerator and unplug from wall outlet remove the defective inlet valve replace with new inlet valve. Now is a great to clean use a air compressor and vacuum and your old crusty frige will be good as new ! Special thanks to Parts Select fast shipping and original ge parts!!

replaced water valve for 50 dollars, saved about 200 dollars by doing it myself

Removed panel from inside the back of the freezer section, by removing four screws. Then, sprayed the ice build-up on the coils, with hot water until all of the ice was melted away. (Note: be certain to plug the drain hole, and use several towels to catch the water drainage. ) Removed the Defrost Heater Element by removing two holding screws. Unplug the unit and pluged-in the new unit and replaced all screws as originally mounted.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

The first sign of trouble was when the water dispenser would continue to come out after you let up on the button. Then water and ice stopped. Changed the secondary inlet value and the main water valve, as well as a 1/4" water line running to the freezer (it was cracked). Water is working. Ice maker is working better than ever. New life for an aged refrige.

I supported door with 2* 6 scrap wood. I used cedar shingles to raise door to correct height.
Using a socket wrench, I removed the hinge from the fridge and the cam assembly from the door.
I installed the new hinge and cam using the shims thatwere behind the original parts.
I removed the 2*6 supports and the door now works perfectly.

Shut off water and disconnected at factory joint at bottom hinge. Unplugged the electrical at the top hinge. Removed the door and installed new bottom hinge and cam assembly. Reinstalled the door and hooked water and electric back up. Part worked fine.

Removed the back panel from the lower part of the fridge to expose the valves and motor. Then the one screw holding the valve/bracket assembly was removed to free the assy. It took a few minutes to figure out how to remove the water lines - popped the colored plastic rings out with a screwdriver and removed the lines. Inserted the lines one by one as they were removed to keep correct orientation. Removed the two electrical connections and plugged into new valve. Installed assy with the one screw. Replaced back panel.