TBG19PABURWW General Electric Refrigerator - Instructions

Removed the 2 drawers and then the glass shelf.
Positioned the drawer slid and tightened to rear screw and the front screw.

Replaced the shelf and the 2 deawers.

What's the big deal? Any 78 year old woman can do it.

First i removed everything from the bottom shelf, removed the glass, then removed the entire bracket assembly. Then removed the front metal strip to expose the front mounting screw, then removed the rear screw. Installed the new part and reversed the procedure.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

Replacing the new part wasn't hard, just very time consuming and frustrating. I had to remove two-thirds of the shelving of refrigerator as broken drawer slide was on the bottom and I had to have room to remove old and replace new. Of course, then I had to CLEAN all the drawers and shelving before replacing them and then, because they were fresh and clean, I had to remove the other third of shelving and wash and replace it. So, it was an hour-long or more time. I love your business, and had no idea I could get so many parts for old applicance and replace them myself, and I am a 70-year-old woman! This was the 2nd time to use your site and I will return to it again when needed. Thanks for prompt and reliable service and a site that makes it easy for a neophyte like me to find the broken part ! Keep up the good work.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!

I followed the directions on the site for the center slide replacement. I had actually called a local store and had him order the first part. It took several days and then I started searching online and found this site.Then I ordered the second part on line and to my surprise it arrived the next day. I was fortunate enough to have lived only about 70 miles from the distributer.Following the directions I found here is how I attempted the initial repair. With the vegetable bins out fo the bottom, I removed the plate covering the front frame by gently prying it off. Then I removed the two screws to losen the bar and lifted out the glass shelf. I didn't have much difficulty removing the frame since the front piece support for the slide rail that fit into the frame was already broken. I also had to loosen the screws on the back rail. I removed the entire frame and then replaced the side rail reinserting it into the end caps. I replaced the back screws and then the front ones .I replaced the glass shelf and then the cover cap for the shelf.
The only problem I encountered was that I couldn't seem to get the back screws really tight and I don't know why.

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

Unscrewed four screws, two on each part, and replaced broken parts, reinserting screws. This is a no-brainer repair.

Removed drawers and glass shelf. Removed screws that hold old slide rails in place. Installed new rails and re-installed cover for vents. Placed assembly back in and installed drawers.

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

Basically I removed 4 screws holding the rails together, did a little cleaning of the existing parts that I would re-use and screwed the 4 screws back in and put it back into the fridge. Piece of cake. If I hadn't cleaned up the old parts it would have taken me 5 minutes.

I pulled out the shelf and removed the 2 screws holding the broken side rail to the shelf frame. I then screwed the new rail in and set the shelf back in.

Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side of the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.

Unplugged the refrigerator then used the cordless drill to remove the 6 screws on the access panel on the back of the fridge to be able to get to the fan. Was able to pull the fan off by hand and push the new fan on by hand. Plugged the refrigerator by in and watched the fan run for a few minutes then replaced the access panel. Really quick and easy repair.