This washer sensor assembly, also known as a motor rotor position sensor, is a genuine OEM replacement part designed to monitor the direction and speed of the rotor during operation. By communicating ...
$80.21
In Stock
Order within the next 10 hrs and your part ships today!
This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a w...
$56.87
In Stock
Order within the next 10 hrs and your part ships today!
This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stop...
$186.67
In Stock
Order within the next 10 hrs and your part ships today!
This is a pulsator assembly, also known as an agitator, for your washing machine. This pulsator sits at the bottom of your washer and is what is used as the main driving force to wash your clothes. If...
$207.89
In Stock
Order within the next 10 hrs and your part ships today!
This drain pump is for washers. Drain pump removes water from the washer during the drain portion of the cycle. Unplug the washer before installing this part. Wear work gloves to protect your hands.
$242.52
In Stock
Order within the next 10 hrs and your part ships today!
This part is the replacement switch assembly for your top-load washer. It contains the switch mechanism and the connecting wire that hooks the door latch to the electrical system of the washer. The li...
$186.67
In Stock
Order within the next 10 hrs and your part ships today!
Getting your LG washing machine back to its top-performing state is quicker and simpler with our genuine Original Equipment Manufacturer (OEM) Motor Assembly Clutch. This part steps in to switch your ...
$155.97
In Stock
Order within the next 10 hrs and your part ships today!
Facing issues with your LG washer? Get back to seamless laundry days with our LG Washer Motor Stator Assembly. Crafted to match specific LG washing machines, this authentic OEM part is here to restore...
$510.00
In Stock
Order within the next 10 hrs and your part ships today!
If your washer isn’t spinning or agitating like it should, this shift actuator might be the fix. It helps switch between wash and spin modes by connecting the motor to the tub. It’s a common repair an...
$80.21
In Stock
Order within the next 10 hrs and your part ships today!
We're excited to share the Cap Cover with you - a genuine, OEM-manufactured part by LG. Specially designed for certain LG washers, it's a critical part of the dispenser cup system, covering up your bl...
$56.87
On Order
Questions And Answers for T1335ADF
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
Removed back of washer with screw driver, Removed outer motor cover with a 17 mm socket (1 bolt), Removed motor stater using 10 mm socket (8 bolts). Left motor plugged in and and tipped to the side exposing the sensor. Unplug and snap off sensor. Reassembled in opposite order. Machine works great. Very easy fix, and perfect fit on part.
1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable supplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.
