SVE47100WC Jenn-Air Range - Instructions

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

pull oven, remove back pannel and unplug and remove high limit switch. Repair was the reverse of removal.

I inserted the door strikes in the proper position and then snapped the panel in place.

Took the (6) screws holding the top of the stove out, then removed the switch screws(2). Then lifted the top, so as I could reach and get at the switch. And then I repeated the above. It was alot easier the second time. Duh I erred the first time and replaced the wrong one and before I relized it, I opened the switch to check out. All in all. I still got satisfaction from doing it myself. Thanks Parts Select

First I turned off the circuit breaker at the control panel to my Jenn-Air stove-top. At 220-volts, don't take any chances with electricity!

Then I removed two screws that hold the burner switch panel in place and lifted up the panel to expose the wires that are connected to all 4 of the burner switches, the exhaust fan and pilot lights that indicate if a burner is turned on.

I used a circuit tester to determine that the power was indeed off to the switches. Again, it is extremely important to respect 220-volts of electricity.

I ensured that all of the wires were already labeled the same as the terminal connections on the switch (i.e. H-1, H-2, P, etc.). If they are not, label them yourself with masking tape around each wire. Then I removed each of the wires connected to the burned out switch with a pair of needle-nose pliers.

Next I removed the two screws attaching the burner switch to the panel.

To install the new switch, repeat all of these directions in reverse, making sure to attach each labeled wire to the correct terminal on the burner switch.

Turn the circuit back on at the circuit breaker. Then test the burner switch and see if the burner heats up. Hopefully, you'll be cooking in no time...............

It would have been nice if basic instructions were supplied ( eg. how to remove switch panel ) but it went rather smoothly.
First killed power the electric stove.
I then removed the screws from the bottom of the panel and then pried the top of the control panel down and then out. I copied the positioning and wire colors.Removed wires from prongs, removed the two screws, replaced old switch with new one .

I removed the 4 screws that held on the front panel as well as the knob of the defective switch. With the panel free, I pulled the wire connections from the rear of the switch with needle-nose pliers. I then removed the 2 screws which secured the switch and removed it. I then reversed the process with the new switch. It could not have been easier.

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.

The hardest part was breaking the caulk seal between the range and the cabinet. An extra set of hands made the job easier, by holding the panel while I connected the switch. The switch was delivered promptly and I am very happy with Parts Select. I found the other repair stories very helpful.

Replace filter

I rremoved two screws and pulled element out about 3 inches. I un hooked the two wires and tested with an ohnm meter to determine the condition of the element. Element was bad so I ordered a new one. Service and price were great. Easy fix. Thank you.
Don't forget to unplug first.

Very easy. 1. Turn off power to oven. 2 move the adjustable grills out to gain better access. 3. There are two phillips head screws that hold a bracket to the back of the inside oven. Unscrew both screws. 4 pull the bake element out about 6". This exposes the two electrical connections. 5. Use a plier and wiggle the slide on connector off of the old bake element. 6. With your fingers, slip the old connectors onto the new bake element. 7. Slide the element and wires back in the insulated pocket. 8. Screw both screws back in. 9. Turn on power and make your wife back you chocolate chip cookies just to "test". Sit in an easy chair and enjoy your cookies. If this took longer than 30 minutes inclding baking the cookies, it took you too long. If the cookies are not good, replace the wife. May take a little loger though :)

unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!

I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike