SHX68T56UC (09) Bosch Dishwasher - Instructions

Replacement was fast and very simple. Was completed in less than 5 minutes.

We followed the video and had no problems with leaks at all afterwards. The parts fit perfectly and the machine is working great again.

easy repair, but the check valve wasn't the problem, it was the float switch that isn't on the tech sheet in the dishwasher or mentioned as a possible culprit anywhere I could find on the internet

There were 5 rollers still in place so I used them to show me how to snap the replacement roller in place.

removed machine so left side water drain matrix was accessible, replaced that unit, reinstalled machine to its built-in location.

The new rack arrived nearly ready to install. The brackets and wheels that connect the rack to the track in the dishwasher were already on the new rack when it was delivered. All I had to do was move some plastic parts from the old rack to the new rack. This is very easy and does not require any tools since the parts snap onto the racks. It's worth taking a moment to study the way each part is attached to the old rack before moving it to the new rack. Pay particular attention to exactly how & where the spray arm tube snaps to the rack. That tube took me two tries to get right. The whole operation took less than 15 minutes.

Removed the dishwasher from the cabinet, laid it on its side, removed the old pump/heater, installed the new and reinstalled the dishwasher. What made this a little more difficult is my dishwasher has a bottom to it that would be very difficult to remove, access to the pump is from the side! I have large hands, not much room to work!

Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.

Initially, I received an E15 error. I evaluated for leaks but couldn't find anything except for water in the bottom of the dishwasher after about 30 minutes of the initial cycle. After discovering the hole in the flow tub, I order the part. It came a few days later & replace the part within a 15 minutes of receiving it. I didn't think it would resolve the issue but it did. Thank you!

The repair was extremely simple. Just lined up and popped them on. No tools needed.

To remove the old cutlery drawer I had to pull the old drawer forward and work the rollers over the stops at the end of the permanently installed slides. To install the new cutlery drawer, I reversed the procedure and worked the rollers on the new drawer over the slide stops and seat the new basket. No tools were required.

As for the crockery baskets, the larger lower basket was very simple. Roll it forward onto the door and lift it out. To install the new basket reverse the procedure. Place the new basket on the door and slide it in on its rollers.

For the upper crockery basket the procedure is more complex. The retaining mechanisms for the upper basket appear to be very complet as they have a number of moving parts intricately engineered. With a little study, it become apparent releasing the locks and levers which keep the basket from rolling out and falling to the floor are well designed to both secure the basket and to remove. Each anchoring mechanism has a lever at the base and by depressing the lever it releases the basket so it can be rolled forward over the stops at the end of the slides. Some manual dexterity is required to maintain pressure on the mechanisms to ensure the basket will be released. The procedure is quickly mastered with a few attempts. The good thing is again no tools are required.

My new tray and baskets are working fine and it is a relief to have the old rusting and deteriorating tray and basket replaced. This is true for both safeguarding the crockery and cutlery form rust and chemical of deteriorating plastics, rusting metal, and bonding agents. More important, I am sure replacing the old deteriorating baskets and tray guards against any potential health issues.

Easily removed the old one by carefully pulling it and repeated this procedure to replace it. Total time took less than 15 minutes

I bought replacement wheels.
I put them on the post, and they snapped onto the vertical post very easily. Job done.

The spray arm makes a slide in attachment to a slide out drawer. It was removed by forcing out of the connection on the back of the drawer and the replacement was installed by sliding it into the same connection point.

Followed the video on your site and it was an easy install with no more leakage.