SHPM65W52N/10 Bosch Dishwasher - Instructions

easy repair, but the check valve wasn't the problem, it was the float switch that isn't on the tech sheet in the dishwasher or mentioned as a possible culprit anywhere I could find on the internet

The dishwasher has inserts that can be raised and lowered to adjust the space between the dishes.
One of the holders broke.
I took out the old one and put a new one in.

1) The hardest part was identifying the piece.
This is the insert holder near the front of the rack, to the right of the cutlery basket (as you face the dishwasher)
The drawings on the site are tiny so it is hard to figure out which is the correct piece
There are 3 different numbers for each piece.
the number on the rack assembly diagram (0647)
the PartSelect Number (PS8728043) and
the Manufacturer Part Number (00616990)
I wound up ordering a number of parts and returning the ones that I didn't need (at my expense)

2) Be sure to take pictures before you remove the old piece. Once the broke piece was removed, it was not obvious to me how it the new piece connected.

Once I had the correct piece, pulling out the old one and installing the new one took no time at all.

Initially, I received an E15 error. I evaluated for leaks but couldn't find anything except for water in the bottom of the dishwasher after about 30 minutes of the initial cycle. After discovering the hole in the flow tub, I order the part. It came a few days later & replace the part within a 15 minutes of receiving it. I didn't think it would resolve the issue but it did. Thank you!

removed machine so left side water drain matrix was accessible, replaced that unit, reinstalled machine to its built-in location.

The new rack arrived nearly ready to install. The brackets and wheels that connect the rack to the track in the dishwasher were already on the new rack when it was delivered. All I had to do was move some plastic parts from the old rack to the new rack. This is very easy and does not require any tools since the parts snap onto the racks. It's worth taking a moment to study the way each part is attached to the old rack before moving it to the new rack. Pay particular attention to exactly how & where the spray arm tube snaps to the rack. That tube took me two tries to get right. The whole operation took less than 15 minutes.

Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.

Simply removed the four screws holding the handle in place, gently removed the handle and inserted the new part. You have to be careful and work slowly in order not to damage the front of the door while getting the snap locks unsnapped.


Once the old part was removed, simply snap in the new part and put the screws back.

Great help in locating the correct part on the phone.

The problem and solution were described on the internet. I ordered a set of 4 wheels for $43+. I received one wheel. When I called Drew told me that the order was correct, but the description on the web page was wrong. He was to sent me a return label, but it has not arrived. Since then I went to the Bosch website, found the set of wheels (Part 10016657) for $42. They have been installed and the problem seems to have been fixed.

Easily removed the old one by carefully pulling it and repeated this procedure to replace it. Total time took less than 15 minutes

The handle fits from the inside of the outer door panel. I removed the panel. The handle is easier to remove if you break it in the middle. I then installed the handle and front panel. Note the length of the screws and their positions.

Followed the video on your site and it was an easy install with no more leakage.

The spray arm makes a slide in attachment to a slide out drawer. It was removed by forcing out of the connection on the back of the drawer and the replacement was installed by sliding it into the same connection point.

Repair was simple once the problem was diagnosed with the inlet valve.
Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched the original and solved the problem we had.

Replaced ‘sump’ housing , seal was leaking on it- replaced inop float on water level warning system switch, and switch itself as well- replaced drain pump motor attached to sump- replaced o-ring seal at water sprayer inlet valve- replaced water inlet plastic assemble on side of dishwasher- replaced drain hose out of sump assembly.

Used YouTube video to understand repair- this is an involved repair in time and complexity- dishwasher eventually gets turned upside down once removed and stripped down, to remove the white plastic water pan , which then allows access to the guts of all the above parts- some critical seals only come with new assemblies, so you are buying that new part to get a new seal and ensure no new leaks from what you took apart.

A rat got under the dishwasher and chewed up the electric’s and the hoses. Only found out when the air light came on drain not working Lots of water underneath as well as all kinds or shoot insulation and rat droppings had to wear a mask affect him use a bunch of Clorox before I could diagnose it a real party And hard to reach corners.
I ordered four parts since I found a better deal on the main electric cable which a rat head chewed through until it had an electrocuted itself. These four parts came in three different boxes and three different deliveries over two weeks. not efficient. But handwashing is over put it all together and it works I soaked the hose in hot water so I could fit it on.