SDE515DAYW Maytag Dryer - Instructions

Remove bottom panel from dryer. disconnect wires off of Limit switch. Unscrew 2 screws, remove old switch. Reverse to install. Important, if limit goes bad you need to replace cycling thermostat or chances are the limit will go out again. (Limit on back wall of dryer). The cycling thermostat is right under the lint screen. Remove 3 wires. Remove 2 screws, remove switch. Reverse to install new cycling thermostat. Toatl cost of 2 parts used 16 dollars and change. Thanks

Terminal Block was cracked and dryer was not receiving enough voltage, causing the heating element not to heat. Here were the steps I took to fix the problem:
1. Turn off breaker to dryer from 240v outlet
2. Unplug dryer from 240v wall outlet.
3. On outside, rear of dryer, remove cover plate and the clamp that the power cord goes through with nut driver or phillips screwdriver and take picture or write down how the power cord wires go to the terminal block.
4. Use nut driver or phillips screwdriver to remove the power cord wires from terminal block and ground wire from dryer body.
5. On top front of dryer, use large slotted screwdriver or some other tool to push in on the two clips in order to lift the cover up on dryer.
6. Take picture or write down how wires are attached to terminal block.
7. Remove wires from terminal block with nut driver or phillips screwdriver.
8. Use nut driver to remove terminal block from washer and install the new terminal block.
9. Reinstall wires to new terminal block.
10. Close dryer cover.
11. Reinstall clamp onto power cord wires and reinstall wires to new terminal block and ground wire to washer body then put cover plate back on.
12. Plug in dryer then turn on breaker.
13. Start dryer to see if it heats now.

I used a large flat head screwdriver to lift top up, then located 2 screws in the top right and left hand side to remove front. Remove the three Phillip Head Screws that holds the assy in place slide out. Mine had 2 metal pieces with wires. I simply unplugged and took metal pieces and installed in the new assy. Remove excess lint put front back on lowered lid and done! 15-20 minutes

Propped the machine up in the front, removed the front panel, the door assembly, and the front drum support. Use a Sharpie to mark wire positions. This will help during re-assembly. To get the drum out, you first have to remove the belt from the motor pulley. Drum slides right out. You will need snap-ring pliers to remove the pulley from the idler arm. I also replaced the drive belt because it was cheap, and always a good idea to replace it when you are this far into the machine if it is a few years old. Re-assemble in the reverse order of disassembly. An easy fix for the average do-it-yourself person.

Remove screws to top of appliance lid and control panel paying close attention to location and type of screws. Lift back of top panel and lift off front top lid until it snaps up. Slide top panel to side and remove upper front panel screws from the inside of dryer one on left and one on right. Be careful to not let front door fall outward. Slide door panel up off of hooks at base of panel. Remove duct assembly by removing three screws located on the inside of the dryer at the front. Slide out and remove air duct assembly.

Removing the High Limit Thermal Fuse was straight forward. Didn't really understand the online instructions but performed a continuity test across terminals and there was no continuity, so I replaced.

Repare took 1-2 hours, next time will probably cut in half now that I know where to remove screws to access motors & fuses and dryer assemblies at base of dryer.

Unable to find a repair manual or accurate diagram, I forged ahead and removed the top and front panels of the dryer. It took two tries to figure out how to thread the belt (nine of my ten thumbs kept getting in the way!), but after a coffee break, the job came together, and I've taken the clothesline down!

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

Dryer stopped tumbling, so bad belt was my first thought. Dryer is in vacation home so did not have immediate access to it to diagnose. Ordered belt and discovered that the poorly designed motor pulley had broken and the belt jumped onto the motor shaft and burned through the original belt. Week 2 after ordering pulley, installation went per YouTube video. Glad I also replaced the belt because it was brittle and cracked. Suspect it had been slipping because sheets would ball up into a log, possibly because the drum wasn't spinning fast enough. Anyhoo, after repair all seems OK.

I removed the dryer front and replaced the door switch.
Next I replaced the drum glide reassembled the dryer.

I first unpluged the dryer. Then I
Removed two screws and removed bottom cover, Then removed the door assembly.Here I had to unplug the light and door switches. I then removed the four screws that holds the tub mount in place, Then I removed the eight screws that hold the blower cover in place, then removed the blower. replaced blower and reassembled in reverse. I started the dryer and it worked fine.

Pushed new knob onto shaft

Early in the life of my dryer, the Cylinder Seal came out. For the past two years I put off buying the part. When it came in, I p[opped the top of the dryer, removed the two screws holding on the front panel, and pulled the Cylinder of the back wall of the dryer. I then placed the seal in the right spot, glued it down and reassembled. About Fifteen minutes of work and a cheap part, and now my dryer dries a l;oad of clothes in an hour instead of three.

The video on the web-site was very helpful in showing how to take it apart. First we remove the power plug from the wall outlet. Then we used flat scrapper to push the top two hidden clips to release the Dryer's top. We used the nut driver to unscrew the two screws that held the front panel. We carefully remove the wires that were connected to switch sensor for the door, and the lights. Next step was to unscrew couple more screws that held the front piece from the main fan housing. At the bottom locate the tensioner of the belt. Release it. Remove the dryer drum with the belt. We took the opportunity to clean off the lint that was all over on the bottom of the dryer. We then could reach the bottom left back of the dryer to unscrew the screws that held the heater unit. Before that we unscrew and release the wires for the Thermal fuse and the limit thermostat which are all located on the heating unit. Then we replace with new pieces. Upon removal of the heating unit we noticed the broken heating element. Next was to place the drum back in. We made sure that the drum lined up with the rear support piece then the front. We rotated the drum just to make sure that it was sitting correctly. Then we screwed the front housing unit. Then we put the front panel back on the hooks at the bottom. That help to line up the front panel with the main chasis. We connected all the connectors to the right terminals. Last was to set the top down on to the chasis. We checked that the duct in the rear is not obstucted. Lastly was plugging in the power cord and testing the dryer. It is working again. Thanks to Part Select's video and parts. Total time was just over half an hour.

I had already taken the dryer apart prior to changing the felt seal. Had oiled the rollers, greased the bearings & vacuumed the whole inside of the dryer out. Had used a high temp lubricant on the seal & had stopped squeaking for about a month. I ordered 2 seals & when they arrived, I popped the top of the dryer off using the putty knife to pry the spring latches. I opened the top up & leaned it against a wall. I disconnected the wiring to the light & the switch in the door, making note of the wiring order. Then used a nut driver to take the 2 screws from the inside out, that holds the front cover in place. Then the same for the 4 screws holding the front bulkhead in place. Then lifted up & out from the unit. Then used the putty knife to scrap the adhesive & old seal off the bulkhead. Cleaned as much of the adhesive off, then applied some high temp silicone adhesive to the bulkhead, placed the new seal on, using some clamps to hold it in place. After making sure it had adhered to the seal & bulkhead. Did the reversal of the above mentioned steps. Moved the unit to laundry room, plugged it in then started it & voila no more squeaking dryer.

remove bottom two screws on lower front panel, remove panel. remove two screws on lower portion of door panel, pull bottom panel towards yourself to release pins at the top. Disconnect wiring for light and door switch (make sure to note what wires go where. Complete removal of front door panel. Remove 4 screws holding cylinder frame in place, lift to remove. remove remnants of old felt seal, use rotary tool to remove excess glue, etc. apply glue (used rubberized gorilla super glue), apply felt seal - allow glue to set up. reinstall in reverse direction from removal. Be sure to use glue as there are no clips or other retaining pieces for the new felt and it will not hold in place. overall pretty easy.