This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the touch pad on the micro...
This is a replacement oven lamp for your microwave. The base is made of black plastic, and the lamp itself is made of glass. The base is approximately 2 inches long and 1 inch wide. The bulb is locate...
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Christine
November 24, 2022
the interior light on the right side of the cabinet blinks and clicks constantly. the microwave still works. any ideas
For model number SCA2000BBB03
Hi Christine, thank you for reaching out. The following parts need to be checked to fix the issue: the Interlock Switch, part number PS237015, and the Oven Lamp, part number PS247334. We hope this helps! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
No consistent heat.
When I insert screw driver into (2) latch holes and move around the unit will heat for several door closing before “no heat”.
I’ll repeat inserting the screw driver and will again have heat.
For model number SCA2000BBB03
Hello Bill, thank you for getting in touch. We recommend you check the door interlock switch, part number PS237015, and the switch monitor, part number PS11766871, with a multimeter to fix this issue. If both work fine, you may need to replace the door latch, part number PS230891. We hope this helps, good luck with this repair!
does this model have a charco filter. it is not vented out side.
For model number SCA2000BBB03
Hi Terry, thank you for the great question. According to our research, your model does not have a charcoal filter; it only has a grease filter. We hope this information is useful!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Turned out the issue was easily solved by replacing a single, inexpensive fuse.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the microwave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
I have a GE Advantium/micorwave oven. It is the model that has the hinges on the side, NOT the bottom. First, removing the door is necessary. The grill has to be removed first, then the door lifts right out. Next the plastic backing on the door has to be very carfully taken off to expose where the new latch has to be placed. Use a flat screw driver or putty knife to go around the permiter releasing the internal, unseen, plastic catches that hold it on. This should be done carefully, to avoid breaking the catches that you can't see. After the plastic is mostly removed putting in the spring is not too difficult, but a second set of hands is almost manditory.
Remove shroud . Two black philips head screws on side, and several on the back side. The two bottom screws on the back are special screws that a philips,straight slot, or hex screwdriver will not remove. I took a dremel tool with a thin metal grinding disc and created a straight slot through the centr of the two bottom screws. This allowed their removal with a straight slot screwdriver. Slide the cover straight back and off. The bulb is located on the top of the microwave connected with one screw. Replaced the bulb. It has two prongs that fit into the holder. Replace screw. Slide cover back on. It slides into retaining splines on 3 sides. Replace screws, and you're in business.