This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
The filter is made of metal and is intended for use with ranges and cooktops. As per the manufacturer, this filter may be 1/2" slimmer than the original, but will still function the same.
This hinge is located on each side of the oven door. The hinges control the rate that the oven door opens and closes, and allows the door to stay open at an angle. This hinge can be used on either the...
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
Sold individually. Lock washers are used with screws when vibration from an appliance may cause the screw to loosen. Lock washers are also used in the electrical components of an appliance to ensure ...
This electric oven bake element with screw in wire terminals is 19 inches wide. It has a terminal depth of three inches and a total element length of nineteen inches. This element is intended for use ...
This thermostat knob is two inches in diameter. It is a black knob with white numbering indicating the temperature inside the oven as well as the 'off' and 'clean' positions. There is also some chrome...
This cartridge receptacle is almost four inches long. It is white in color and is made of ceramic.
$60.81
In Stock
Questions And Answers for S160
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kathy
December 22, 2019
My exhaust fan has quit working. This stove is vented down through the floor. Do you have a replacement for it?
For model number S160
Hi Kathy, thank you for your question. The part you are requesting on has been discontinued and we have no known replacement listed in our system. We have no further information. You are welcome to contact the manufacturer of the part to see if they have recently released a new substitute. This was the part number: 12001311. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Mike
November 26, 2023
What are the steps for removing the oven door on a Jenn-Air S160 Electric Oven?
For model number S160
Hello Mike, thank you for asking. We are providing you with the instructions that will help you in removing the oven door.
1- Open the oven door and rotate latch towards oven door to unlocked position.
2- Partially close door to engage door latch locks.
3- Grasp edges of oven door. Lift and pull oven door toward you and remove it.
We hope this helps!
Was this helpful?
Thank you for voting!
Charles
September 2, 2022
Do you have a replacement for a heating element cartridge
For model number S160
Hello Charles, thank you for your question. Yes, we have several. Radiant Smoothtop Cartridge Assembly in black PS8768540, Stove Cartridge Assembly PS9491819 as well as others that can be found in the section on our site entitled Jenn-Air Cartridges and Accessories( Designer Line). If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
Most of the repair was obvious as I took the blower apart before ordering the parts. Unfortunately the new motor was significantly larger than the original motor so I had to um. Adjust the position of some of the other parts to fit it in. There was a sheet metal flange that was installed on the other side of the blower from the motor which was designed to focus the air flow into the blower. I used a hammer to ajust the angle of flange so it no longer extended as far into the blower housing.
It works just fine although its a bit louder than the old motor was.
1. Killed power and removed the regulator's knob, noted the position of the old control. 2. Took off the cover for the center vent and loosened the two screw holding the housing in place--the screws didn't have to come out completely as it is a U-shaped friction hold. 3. Unscrewed the two screws holding the old control switch in place--lifted the housing enough to get at the old switch and carefully pulled it loose--it was a front burner so the control switch was about as far back as it could be but still wasn't that hard to get at. 4. Turned the new switch to orient the wire connectors, then, using a needle-nose pliers, removed each friction connector, one at a time, and fitted them on the new switch (note: one of the wires fitted best if it went under as opposed to around the base of the new switch). 5. Replaced the control back through the housing and screwed it in place, making sure the orientation of the control matched the way it looked originally. 6. Slide the housing back over the two screws and tightened, replace vent. 7. Replaced the knob and turned on the power.
(The above took me about twice as long to write as it did to make the repair and I write professionally but am not a professional electrician.)
Also, I bought a second control switch because, given the age of the unit, I'm sure another one will go. The second one will assure that it won't happen :-).
