This is a 40W/120V ice maker assembly for your refrigerator. Ice maker assemblies are designed to continuously make ice cubes by supplying water through its valve, freezing it, and then ejecting the c...
$133.98
In Stock
Order within the next 5 hrs and your part ships today!
To ensure optimal functionality and energy efficiency of your refrigerator, the Samsung Refrigerator Door Gasket (part number DA63-07733A) is designed to create an airtight seal on the door. This seal...
$110.28
In Stock
Order within the next 5 hrs and your part ships today!
This white-colored flipper or mullion assembly serves as a seal mechanism found between the French doors of your refrigerator. It measures 36 inches in length and 2 inches in width. Positioned along t...
This left handle end cap assembly is designed to secure the refrigerator door handle while concealing the mounting hardware for a clean, finished appearance. Installed on the left side of the handle a...
This roller wheel axle pin (part number DA61-01920A) is for refrigerators. Roller wheel axle pin DA61-01920A attaches the roller wheel to the roller wheel bracket. Wear work gloves to protect your han...
$5.29
In Stock
Order within the next 5 hrs and your part ships today!
This condenser fan blade (part number DA31-00010D) is for refrigerators. Condenser fan blade DA31-00010D moves air across the condenser coil to cool the hot refrigerant before it enters the evaporator...
$23.71
In Stock
Order within the next 5 hrs and your part ships today!
Questions And Answers for RF18HFENBSR
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
William
March 26, 2020
Water is accumulating on top of the crisper drawers. And on one side it has frozen.How do i fix this?
For model number RF18HFENBSR
Hello William, thank you for your inquiry. There may be a pin hole in tubing present in your appliance, allowing water to escape, or this issue may stem from condensation getting into the appliance via a defective gasket, which is allowing warm air into the unit. We would suggest checking the gasket(s), as well as the water line that carries the water to your ice maker to ensure those components are fully operational. We hope this helps.
5 peoplefound this helpful.
Was this helpful?
Thank you for voting!
Andy
December 29, 2019
Remove cover to replace fan
For model number RF18HFENBSR
Hello Andy,
Thank you for your question. The cover for the fan grommet for your model is under part PS4153930. We hope this helps!
Back interior panel will not come loose. Removed 2 screws from bottom,
For model number RF18HFENBSR
Hello Mark, Thank you for the question. Once you remove the shelves, there will be one screw at the top of the shelf rail in the center as well as two on the bottom of the cover assembly that would need to be removed. This will allow the cover to pull free and move enough so the wires can be disconnected from the back wall. We hope this helps!
Pull out old one from right top. Wipe track with a cloth and some Windex. Wipe with clean cloth place gasket over where it will replace old. Start right top push into track. Time 10 minutes once all seated again go over the entire gasket check all in track push with thumb easy replacement!!
I watched several repair videos and decided I could do this because I have been doing mechanical work for over fifty years.The videos convinced me it needed replaced it is a 2009 model I bought new. I ordered the new part from parts select it came in 3 or 4 days.The hardest part was removing the freezer door and reinstalling when I was done.That wasn’t complicated just awkward.Removing the ice maker was simple and replacing it with the new one was easy.There was a protective plate on the front of the old one that wouldn’t fit on the new one.So I left it off.So far it has been working very well.
