RE960PXKW1 Whirlpool Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, Removed the old element and installed the new one

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Simple to do. Remove old element, remove screw holding socket, cut the socket wires with 2 inches to spare, assemble the newsocket and wires with heat shrink tubing, strip range wires, apply the wire nuts as instructed and shrink the tubning with a heat gun.

Screw on the socket to the range. Shut the lid and install the element.

The replacemnet screw is thicker than the original one, so you might want to drill out the hole very slightly. I did not but the resistance was high on getting the screw fully seated.

Works great

First, shut off the power at the breaker panel. Next, I simply unscrewed the screws holding in each element, disconnected the leads, reconnected the leads to the new elements, positioned each element & reinserted the screws. A suggestion: Before loosening the screws, a light shot of PB Blaster or similar might help.

I didn't. Don't know how to get to light bulb to change it for this specific model

Two screws held the element in place, removed the screws and pulled the piece out.
Back of piece has two wires attached, unplug them then attach the new element and replace the two screws to remount.
First make sure the breaker to the range is turned off before starting the repair.

simply turned off power. took old element out, held in by two screws. pulled out far enough to take off wires. removed and replaced with new element. that was a purfect fit. Works great.

I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just 4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .

1. Turn off circuit breaker, pull out element and remove reflector pan.
2. Unfasten terminal block mounting screw and remove terminal block from casing.
3. Cut wires as close to defective terminal block as possible (not as per instructions) since you will need the maximum possible length of wire.
4. Slip on heat shrink sleeves, strip stove wires and connect to new terminal block per instructions.
5. Heat shrink sleeves per instructions.

Removed 2 screws holding element in place. Pulled out element to access two wires. Slid off the old element connectors. Placed new element in place and attached the two wires. Pushed it back into place and replaced the screws. Done in 10 min max.

SUPER EASY! The part arrived very quickly. I turned off the circuit breaker, unscrewed the few nuts, pulled out the element and reversed the process. 'works beautifully! Thanks so much.

removed old Plug-in block by removing 1 screw and cutting 2 wires. (Screw was so tight and rusty that I had to use vise grips to remove it). Installed new Plug-in block with wire nuts and heat shrink wraps. YOU just have to make sure the wires are seated in the block properly. This job was much easier than I anticipated. The burner works great now!

took out the old heating elments and cleaned the bottom & top of oven with out the elments in, which made it alot easier then put new ones in. They were very easy to do, just make sure you watch how you took old ones out and don't loose the screws cause you use them to put new ones in.

Open oven door. Still power to the wall, but all Knobs in "OFF" position. two phillips screws, pull old element back, and disconnect both leads. Put the leads on the new element and reinsert with two mounting screws. Simple.

Unplugged old burner elements. Popped in new burners. Turned on the burners to test.