PWE23KSDASS General Electric Refrigerator - Instructions

REMOVE LOWER DRAWERS, SHELF AND BACK EVAPORATOR COVER AND REPLACE SIEZED EVAPORATOR BLOWER MOTOR.

EXCHANGED THE LED LAMP ASSEMBLY. ONLY DO ONE AT A TIME AS THEY ARE WIRED IN SERIES!

I replaced the three sensors, 2 in the freezer 1 in the refrigerator. This was rated as the most common problem. Did not fix the problem. I then checked the ohms on the new sensors then the old sensors they were all within .5 of each other. So I got smart and went down the list of causes on their list. I emailed partselect and asked what the parts should read. They replied with that information and it turned out to be the voltage converter on the compressor. I ordered the part on friday payed for overnight delivery and it arrived tuesday. This as you can imagine makes me angry. But the part was easy to install and my refrigerator started working right away. I would advise anyone with this problem to start at the top of the problem list use a multi meter check everything on the list and only replace part or parts that don't come up to standards. This will save time and money and hopefully fix the problem the first time as you are not switching out parts and hoping that it solves the problem.

as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapped the new switch into place.

10 minutes total.

Removed the bad inlet valve and installed the replacement. Very easily done. The replacement part made the repair so simple and saved me a huge amount over calling a repair man. It did not take any special knowledge.

Repair man thought it was the control board and an issue with a relay on the board. Purchased the new board but found out the board was fine, and it was the recirculating fan that would go out intermediately.

Tried ordering that part from Part Select since they have been great, but GE discontinued the part and their was not a replacement available. After much research, found the new replacement part number and ordered that, it went in quickly and for now seems to have solved the problem.

Watch this very good refrigerator evaporator fan replacement video

Literally turned off the water to the refrigerator, disconnected the lines from the back and took one screw loose from the inside of the unit. Slid out old filter connection and slid in the new one and did reverse process.

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

followed install on line

You have to remove the shelves and drawer's along with the drawer mount. there is a wiring harness you need to unclip to remove the crisper electrical panel

There are six nuts to remove the lower panel at the back of the compartment where the lower drawer normally is. no need to completely remove the panel, you only need to get wiggle room to remove the fan at the base of the center panel.

There is a small triangular cover used to conceal the fan wiring harness on the right side of the center panel that you can use the putty knife to slip in on the center panel side to unclip and remove

Use the putty knife and slide it down both sides of the center panel that runs vertically to unclip it - at the base of this panel is where you'll find the condenser fan, you should be able to wiggle it out - there is a built in clip on the lower right side of the center panel that you can slip the wiring harness out of - for me this was the hardest part of the replacement as it was just awkward.

After it's removed slip in the new fan and seal and reassemble. I think the whole operation took maybe a half hour - 40 minutes. It's pretty easy all said and done.

The glass fits easily under a plastic ridge that is the frame holding the 2 vegetable drawers below. Slide the back side of the glass under the ridge, and then gently place the front of the glass in the groove where it goes on top of the vegetable drawers.
Its Super simple, and takes literally 30 seconds to complete.

1. Turned power off.
2. Removed 2 screws holding plastid plate which connected electrical wire from mullion to door (requires Torq-tip screwdriver).
3. Unplugged wire plug behind the plate.
4. Lifted up old mullion from 2 slots holding it in place to remove it from door.
5. Inserted new mullion into slots on door.
6. Connected electrical wire to plug inside door.
7. Screwed 2 screws to reattached plastic plate to door.
8. Turned power back on.

After looking up what might be the problem, I ordered a new control
board. It was extremely easy to replace. Unfortunately it was not operational. I had to replace my refrigerator. The return process was very easy and my refund was processed quickly.

Remove the screws from the two door pivot covers. Remove the covers and set aside. Remove the screws from the control board; disconnect the electrical connections; remove the door light switch, install door light switch then reinstall everything.