Models > PVM1873SN2SS > Instructions

PVM1873SN2SS General Electric Microwave - Instructions

All Instructions for the PVM1873SN2SS
91 - 105 of 162
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
part was cracked
removed old part and replaced
Parts Used:
Glass Turntable Coupler
  • BRUCE from MONROE TWP, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave would run but not heat
Removed the control panel, one screw at the top. Removed 2 screws on the door switch holder and removed the door switch. VERY EASY.
Parts Used:
Monitor Door Switch
  • Timothy from MAYSVILLE, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The center of turn table broke. A small plastic part that goes under the glass in center.
We took out the broken part, it came right out,and put new part .
Parts Used:
Glass Turntable Coupler
  • Kathy from LEWISTON, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The coupler broke , glass turntable not turning
Received part installed in less than one minute, easy fix alignment of part in shaft pressing down into position
Parts Used:
Glass Turntable Coupler
  • Timothy from LAKE WALES, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turntable Replacement Motor was a larger diameter than the original
Drilled a new tap hole in the base-plate to match the larger diameter motor.
Parts Used:
Turntable Motor Glass Turntable Coupler
  • Edward from DENVER, NC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic tabs on Cam louver broke off and would not remain attached to microwave
Simply installed new cam louver to microwave with two screws. End of job!!
Parts Used:
Assembly-CAM LOUVER
  • Joe from Queensbury, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken turntable coupler
removed the bottom panel (6 screws), disconnected the two power terminals, and losened the turntable motor. installed the coupler from inside the microwave, replaced the motor, re-connected the power terminals, and bottom panel.
Parts Used:
Glass Turntable Coupler
  • Ronald from Pinehurst, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken light lense
Removed one screw, installed new lense in lense frame, rescrewed. Done.
Parts Used:
Glass Light Lens
  • George from Marana, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken lens.
Used a phillips head screw driver and loosened the lens frame under the microwave. Removed the broken lens and replaced it with the lens ordered. Put the lens frame back in place and secured it with the phillips head screw.
Parts Used:
Glass Light Lens
  • Gary from Warren, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
time would count down but unit would not run & heat.
remove cover, unplug secondary door switch (top switch)
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.
Parts Used:
Secondary Door Switch
  • Bill from Shawnee, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat.
Replaced the fuse. Result; did not fix the problem.
Parts Used:
Microwave Fuse
  • Mack from Jacksonville, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dropped the glass cooking tray while cleaning
after a couple of misfires, got the correct size tray, and replaced it in the oven.
Parts Used:
Glass Cooking Tray
  • Lucinda from Burke, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
glass light lens were broken
All one has to do is use a screw driver to remove the screws, one per lens.
Then lower the lens bracket, bend the 4 tabs holding the
lens, remove and replace the lens and screw the brackets back in place.

Less than 10 minuits.
Parts Used:
Glass Light Lens
  • Hugh from Slippery Rock, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat
Replace the fuses
Parts Used:
Microwave Fuse
  • Edwin from New York, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven wouldn't heat
remove cover-unplug wires from secondary switch-remove switch-snap in new switch-plug in wires-replace cover-works great. very easy to do.
Parts Used:
Secondary Door Switch
  • Bill from Shawnee, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the PVM1873SN2SS
91 - 105 of 162