PSC25MGSCBB General Electric Refrigerator - Instructions

I removed the two screws which released the door stop. I then put the new door stop in place and installed the two screws. Job Done.

There were not detailed instructions provided with the parts, however, it was fairly simple to determine how to remove the old part. First, I removed all the shelves. Then I took out four screws holding the top light cover. The plasic around the back center column was removed with a pannel tool. The plastic around the water filter was also removed. The old Fresh Food Air Inlet was then able to come out. Remove the connector. Reinstall per instructions provided. Install the other parts in order they were removed.

Part arrived very fast as ordered..need to pry old switch out from top..use care to push the retainer down..after old switch was 1/2 out, I used a putty knife for better leveridge.Remove wire connector...after plugging in the wire connector to the replacement switch, make sure the switch is properly positioned so the switch will depress when door shuts.

Just pop the old one out, careful not to lose the wiring inside the ref wall & popped the new one in.

opened refrigerator door located water filter location in right back corner unscrewd 1/2 turn and out it comes without shutting off water it is a snap to do by anyone and shipment was really quick thanks. People do not call a service tech for something this simple even a child tall enough can do it.

On the PartSelect website, I chose the 'refridgerator is too warm' problem choice. The site sugested replacing the sensors so I purchased them. The drain trough on the refrigerator side was leaking and it and the defrost thermostat were not too expensive so I bought them too.
Once the parts arrived I installed them. I had already disassembled the inside of the freezer. The sensors and thermostat had to be connected electrically. So I cut off the old parts and stripped their wires. (the new parts' wires were already stripped.) I then used wire nuts to connect the new wires to the old and stuffed the wire back into its compartment and installed its cover. The defrost Thermostat has to be clipped to the refrigeration line. So after attaching its wires I had to work it into its place.
I then reassembled the inside of the freezer and let it sit for an hour before turning it back on. Once it was turned on it seemed to work well, but after only 3 or 4 days the coils began freezing over again.

Turned off power, removed cover from Ice maker, checked resistance across thermostat for zero (read open), all other switches read proper value (when activated). Ordered and received thermostat. Removed Ice Maker from freezer, removed two screws holding ice tray to Control Assembly. Removed Thermostat and replaced with new one. Applied Silicone Sealant to face of Thermostat for adhesion to ice tray when assembled. Remounted Ice Tray to Control Assembly and remounted in freezer. Works Great...

Remove lower front panel, disconnect damaged union from water hose under freezer door, replace with new union, tighten and reattach front panel. No more water coming from under the unit. Ice maker and dispenser features returned to working order!

remove by hand turning old and replacing new by turning by hand.Lifted out old grill and placed in new one

Thanks to others who also gave some detailed instruction on repairs I was able to do the same. I have a GE Profile side by side refrigerator/freezer Model No. PSC25PSSCSS The first repair I did was to remove/replace freezer defrost thermostat sensor that is cliped to condenser tube I snipped the wires close to the thermostat and pulled it off the tube I stripped the ends of the wires and twisted the strands then placed a piece of heat shrink tube onto the wire pushing it away from the exposed wire then I soldered the two color coded wires together then I pulled the heat shrink over the conection and used a lighter to heat up the heat shrink until it sealed the conection repeating this on the othr wire as well. I then removed the Old defrost Heater element by removing to screws then I disconected the two wires by simply pulling the connector plugs off both ends of the heater element assembly. This fixed the freezer being too warm for a short time but it started getting warm again that's when I noticed the defrost fan was not working, when you have the door open to freezer push the door switch in you should hear the fan come to life and blow hard. The fan was replaced I had to remove everything to get to it it's pretty simple to do it just unplugs make sure you order the right fan though My fan comes with the Thermistor already integrated into the plug this makes it easier. This fixed the problem with both Freezer & Refrigerator The Temperatures returned to normal Freezer 0 degrees Refrigerator 37 degrees I also checked out the refrigerator side Condenser I noticed only that the Condensate pan was starting to rust so I will remove it and use some Muretic acid to clean it up and then spray it with some Cold Gavanize with Zinc you can get this spray paint at Home Depot it seals and prevents rust. Or you can order a new one for about $ 16 bucks but it will start rusting just like the old one did eventually if you do order a new Condensate Pan I suggest spraying it before you reinstall it so that it will not rust. Greg H. Eldorado, AR

i used the video it showed on the site or iwould not have been able to do it

First I turned the refrigerator and water line off. Then moved to the freezer section, followed the directions, removed the two screws. Directions state to not remove them but I had to in this case. Unplugged the ice maker and removed it from the freezer. I installed the two mounting screws then tried to plug the electrical connection back in but had to use the adaptor cord furnished in the kit. The cord was a little long but I tucked it in and mounted the ice maker. Turned it on then turned the refrigerator and water back on and in a few hours had ice! Very easy to do!

Because the lever was broken, when you close the refrigerator door, the freezer door would unseal slightly causing frost to build up on the inside and outside of the door.

After removing the base grille, the repair was made by simply placing the new part in the slot where the old part was then re-attaching the spring from the part to the hook in the base of the refrigerator. Now replace the base grille with the two screws. Time: About 10 minutes. Tools: Phillips screwdriver, needle nose pliers.

removed 3 screws unplug and remove old unit. install two screws install new ice maker, tighten screws plug in and turn on. had ice in 20 min.

I replaced the three sensors, 2 in the freezer 1 in the refrigerator. This was rated as the most common problem. Did not fix the problem. I then checked the ohms on the new sensors then the old sensors they were all within .5 of each other. So I got smart and went down the list of causes on their list. I emailed partselect and asked what the parts should read. They replied with that information and it turned out to be the voltage converter on the compressor. I ordered the part on friday payed for overnight delivery and it arrived tuesday. This as you can imagine makes me angry. But the part was easy to install and my refrigerator started working right away. I would advise anyone with this problem to start at the top of the problem list use a multi meter check everything on the list and only replace part or parts that don't come up to standards. This will save time and money and hopefully fix the problem the first time as you are not switching out parts and hoping that it solves the problem.