PSC25MGSBWW General Electric Refrigerator - Instructions

This is the second or third time this cup has broken. Maybe we use more crushed ice than the average family, but you would think this part could be more durable. Anyway, I digress. This is about the repair. Four screws removed around bottom of tray, one screw removed for some bar that mechanically opens a door to allow ice to fall out of the tray, and two butter knives used to release tabs around the screw components... and we were done.

Raised side of fridge enough to get 1/4" ratchet with 1/4" socket under roller wheel assy. Removed three hex-head screws to separate damaged wheel assy from fridge frame. From panel below fridge compartment, backed-out stripped leveling screw. Mounted new roller assy and then threaded in new leveling screw from front. Lowered fridge and adjusted leveling screw for proper height. Suggest putting a 2x4 under fridge for safety when hands are under unit.

Remove back panel on bottom of fridge to access compressor area. Remove screws from water solenoid and water valve and push to the side so the side of the compressor can be accessed. Then locate the inverter box. You will find a Phillips head screw on the bottom of the inverter. This is the only screw that hold the inverter in place. Remove the screw and tilt the inverter box forward away from the compressor, then lift the box out of the the holder. You may have to wiggle it a bit to get it out. Remove the plug that attaches to the compressor and then with the power on check your voltage coming to the compressor. It should read 120 volt. If it doesn’t your inverter is bad. Remove the other plug on the inverter box and pull the box out.
Reinstall the unit in reverse order. Use the appropriate jumper to plug into the wire connection going to box and then plug it into the connection off the fridge.
Once everything is reinstalled and before you put the back panel on plug your refrigerator back in and you should be able to hear the compressor working or feel the top of it to make sure. If it’s working you are good and can reinstall the back panel.
It will take 4-5 hours to come back to temp if it’s been off for any length of time.

Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed

pulled out refer. found leak at corner lower back, pulled off lower cover. found valve for icemaker leaking. looked in owners/inst guide, pulled up on computer, identified part, called, order overnight part. recieved part & installed, repair complete & successful.

Shut off water supply. Unplugged refrigerator. Removed cover. (6 screws -- nutdriver will come in handy). Removed screw securing water valve to frame (again the nutdriver). Unplugged red and white power connectors to solenoids. Using channel locks, loosened nut holding main water supply to valve and removed. Depressed compression fittings to valve and pulled out plastic water lines that supply water dispenser and ice maker. Reconnected main water supply to new part. Pushed both water lines into respective fittings of new part. Reconnected power supply to solenoids. Attached new part to frame with screw. Replaced back cover. Turned water supply back on. Plugged refrig. back in. Problem solved! Savings = $300!

Removed the ice maker from the freezer. Unscrewed the outer cover/base of the ice maker. Unscrewed the long lever that opens the ice chute. This freed up the feeder coil enough to pull it out enough to replace the cup drive. Once I replaced the cup drive, I laid it back down into the ice maker bin, reattached all the screws and it worked! The old cup drive had a tine broken off which would not allow the feeder coil to turn. It seems like a weak part and I anticipate I may have to replace it again in a few years.

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

replaced with new connector and it worked great. also replaced the water filter and that was super easy!

Removed ice bucket and observed the plastic drive bushing for the auger had the drive dog broken off. I removed the four screws on outer shell for the ice bucket, removed it and found the auger had key stoned a hole in the ice tray housing. At that point I decided to replace the ice bucket and auger assy. The new one works fine.

I removed the ice from the tray, took out the four screws from the tray, pulled up the metal spiral took out the old drive cup, replaced with the new one, replaced the screws and put the tray back in the freezer. A piece of cake. Thanks for your prompt service and the reviews on how to replace.

Replacing the water filter with the new style water filter was no problem...twist to the left, drop the old filter, line up arrows on housing and new filter, twist to the right and done.

Ice maker was always crusing ice. There is a spring deflector wound around the actuating rod towards the back of the ice dispenser. Pulled the ice dispenser out, slid the damaged spring off, and slid the new spring deflector on making sure to engage the actuator rod to restore it's action. Easy fix.

I pulled-out & unplugged the refrigerator. Removed the screws to gain access through the lower back panel. The water valve is on the left side as I face the back of the fridge. It has one screw holding it to the frame of the fridge. Once it is free, the main water hose is unscrewed and the two out-let lines were pulled-out. If your valve was not ruined prior to this, it is ruined now, as the lines will not re-seat. Then everything is done in reverse order. I did cut 1/2 inch off of the two lines so that they reseat into the new valve. Just push into the valve and they are good.

It was a simple remove and replace. The new part fits directly in place of the old part. Its a pain to remove the light but once you get the light out the job is simple. The light must be pried out gently. It is snapped in place toward the air inlet cover and needs to be pried loose. Once the light is out there are 4 screws holding the air inlet cover in place. Remove the 4 screws and unfasten the wiring harness. Once the screws and wiring harness are disconnected remove the old part. Reinstall the new part in reverse order.

After lots of research online, i narrowed my problem down to be the double outlet water valve, behind the fridge. My biggest problem was getting the refridgerator out of its spot, but after that it was pretty simple to change. I took the cover off the bottom, in the back of the fridge, then i removed the inlet waterline (after i turned off the water supply to the fridge). After that i removed the screw that holds the valve to the framework. Now i pulled off the two other waterlines from the old valve and moved them, one at a time, over to the new valve, along with the wire harness. The rest of the instalation was reverse order. Simple fix that im glad i didn't pay an expert to do!