PSB42LSRBV General Electric Refrigerator - Instructions

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

I changed the filter first as this has happened before when the filter got too old. Still did not work, so ordered the double outlet water valve as the ice dispenser was working. The part was easy to install with the video directions. However, water still did not dispense. Felt the water coil behind the crisper in the refrigerator and it seemed kind of hard. I wondered if it was frozen. Took a hair dryer to it for about 45 seconds and then tried the water again. Voila' This time it worked. Apparently it WAS frozen. I may have not needed to change the filter or water valve, but everything is working fine so I will leave well enough alone.

I thought it must be the water valve leaking by so I ordered one and put it on myself which was a very easy job. It fixed my problem and everything works fine now. First I unplugged the refrigerator shut off water line block shutoff valve. Then I removed the back plate on refiigerator. Then I removed the water line from the water valve. After that I unplugged the two wiring harnesses. Then I removed the two plastic water lines from water valve. then I inbolted the water valve from refrigerator. Then I got new valve, plugged both water lines into it, plugged both wiring harnesses back into it, hooked main water line back up then turned water back on.

Took the old filter out and put the new one in.
Easy Breezy!!

My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After working with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!

unscrewed old bulb and screwed in new bulb. checked and new bulb works great. less than five minutes to complete.

Unscrewed old bulb, inserted and screwed new bulb into place

Unplug the refrigerator. Gently pry old switch out with screw driver. Move wires to connector on new switch with needle nose pliers. Pop it back into the hole. Plug back in. Peek inside to see the lights working.

replace a new blub

Screwed bulb in and Light works!

Easy

Video is a great but still need to read the instuctions because there are parts you may need on the old ice maker. Saved myself a bit of money by not having to call a repairman. The process was very simple. I am glad I did it myself. Thank you Parts Select!

Had the wife shut the water off, while I was on vacation. Came home pulled the refrigerator out. Had an issue earlier in the year with a leaking hose. Discovered the valve had many pin holes and was going to need to be replaced. Went on line to Partselect ordered on Saturday. It was easy to determine if I had the right part. Purchased and received on the following Tuesday. 30 minuted later the refrigerator was back up and running with ice and cold water. Have used Partselect before always a great experience

unplug refrigerator. Remove Ice bin then remove the cover off the ice maker,(slides off from bottom then lift off top) no reason to remove ice maker completely. Remove center gear screw and remove main gear from Ejector blade. remove (3) screws holding the front plate. The motor and switches are attached to this plate from behind, do not remove the nut from the from the stud that adjusts the travel for the motor. The Motor and switches will come upt with the plate and the shut off arm will come out of a hole in the top right. Its ok just be careful when you put it back to get it in the hole. remove the old cam and replace it wint the new one and reassemble. Its a bit tricky to get all of the microswitches over the new cam just carefully wiggle the plate and cam and don't push too hard. once everything is lined up it should go back together and you can replace the screws and main gear :)

Pulled out broken switch with flat head screwdriver and replaced with replacement part purchased from partselect. Easily plugged in new part and replaced.