PLD4555RFC1 Frigidaire Dishwasher - Instructions

Removed screws and put new bottom gasket in old one just fell out.

The unit would not pump the gray water out so I immediately assumed it was a bad pump. Ordered the part and had it the next day. After taking things apart I realized it was a clogged discharge hose and the original pump was still good. Since I had the new pump and everything was already disassembled I decided it would be a good insurance policy to replace the pump anyways. Easy to install. I didn't even have to pull the unit out. Just did it from underneath.

Replaced the entire top rack with spray bar.

I removed the bottom front of the unit, removed broken friction cable, hooked the new friction cable to the door, attached the cable to the spring, then reattached the spring in the hole provided in the back frane of the unit... Dissappointing how cheaply made these parts are, the dishwasher is just over 1 year old, these friction cables should be made to last longer....

I researched the problem we had with our dishwasher and found the Parts Select website. My husband and I figured out how to remove the broken part and I selected and purchased the replacement.

The part was shipped quickly and when it arrived I changed the broken part with the replacement in less than five minutes. It seems to be working just fine.

I have added Parts Select to our "favorites" in case we have problems with any of our other appliances. Thanks Parts Select. :)

The nut was split down one side, so I first tried to sauder the nut back together. Saudering never goes well for me anyway, but I couldn't get a good enough seal around the nut to make it fit tightly. Then I had to cut off the clear plastic shield to get down in there, just before realizing you could just pull the white wire firmly and it would come loose from the nut. All I had to do then was unscrew the original nut, and screw on the new nut. Then, luckily I had mistakenly ordered an extra clear plastic shield and could replace the one I had previously cut. Dishwasher now runs like a charm!

It is rather easy to repair. After you remove the screws that secure the top of the dishwasher to the countertop you can slide the disherwasher out far enough to gain access to the hose. The hose pulls off after you slide the spring clips down the hose far enough so they no longer grab. Then simply reverse the order and you're done. Less than 30 minutes and you should no longer have to hand wash your dishes!

Easiest repair ever. Part came quickly & came fully assembled. Just screwed the part on by hand and it has worked like new ever since. The original part is 3 separate pieces but the new part was all in one & fit perfectly.

Upper spray are assembly simply screws onto the threaded fitting of the inside ceiling of the dishwasher.

The bottom door gasket simply slides in place. both were done in less than 5 minutes. Be careful the gasket only goes in one way. But it is obvious what way it goes in.

I turned the power off at the circuit breaker. I then took the access panel off the dishwasher at the bottom. I pulled the wire off the connector. I used a plied to remove the broken washer and replaced with new part. I put everything back in reverse order and ran the dishwasher. I than checked for leaks over two days while the machine was running and everything was fine. Thank you Parts Select for saving me $500!

found spray arm on the rack looked at the top of rack saw a nut screw the nut looked at the clip found the ears broke off easy r&r.

The repair went very easy. Just opened the door , and pulled out the worn seal. Lined up the new seal and carefullly pushed new seal into place. Seal pushed in very smooth.

Removed front of door to see how gasket was installed. removed door for proper cleaning of gasket area, removed old gasket cleaned area and installed new gasket in holder notch, reinstalled door adjusting alinement, reinstalled door front.

Had to pull the dishwasher all the way out, but once I removed the insulation surrounding it I found the vent on top. I removed the old vent, unplugged the old wire harness and plugged in my new one. Installation couldn't have been easier!

Lower the door and remove bottom dish tray. Feel with fingers the area where gasket will be pulled from (just below bottom door edge) Pull old gasket from door edge into direction of inside dishwasher. Insert new one in same orientation as old (small slit to right side). New gasket strip will seat into door bottom.