This OEM ice and water filter fits side-by-side and bottom-freezer GE models. The most common reason you would need to change this part is if you have never updated your model and it is no longer filt...
This is a replacement spring pin for French door-style refrigerators. This part is made of white plastic and is approximately ½ an inch in length. If the mullion that keeps the doors closed is not wor...
This part is the replacement French door hinge for your refrigerator. It is made of white plastic and is approximately 1 ¼ inch by 1 inch. The French door hinge can also be known as the flipper hinge....
Assembly CASE-ICE ROUTE
This dispenser ice chute door and funnel assembly is for refrigerators.
Dispenser ice chute door and funnel assembly opens to let ice through when dispensing into a glass ...
This part houses the water filter and connects the water lines.
$331.55
Special Order
Questions And Answers for PFSS9PKYASS
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Stanley
December 9, 2019
What are the measurements of this refrigerator?
For model number PFSS9PKYASS
Hello, Stanley and thanks for writing.
For your convenience, we have attached the link to your manual with repair instruction. We hope this helps. Good luck with your repair
https://partselectcom.azureedge.net/assets/manuals/4665626988EE2ED776651E5A3CCD08594FE24AB6.pdf
2 people found this helpful.
Was this helpful?
Thank you for voting!
Mike
February 24, 2020
My freezer is not cooling all the way (frig side is fine), all the fans are working and the compressor is working. I think it may be the inverter (GE p/n wr55x10960). Do you have test instruction that i can run to see if the inverter board is bad ?? i am very good with a multi meter
For model number PFSS9PKYASS
Hi Mike,
Thank you for your question. To verify if the inverter board is bad, you will need to inspect it for signs damage, wear or burn marks. If it shows any of these signs, it will need to be replaced. If your freezer section is too warm, you should also check the temperature sensor, the main electronic control board and the defrost assembly. We hope this helps. Thank you and have a great day.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Sonia
December 16, 2021
Is there a way to trouble shoot the icemaker before I buy the part. It stopped making ice.
For model number PFSS9PKYASS
Hello Sonia, Thank you for the question. If the Ice Maker is not making ice, we suggest checking the water lines to the Ice Maker to make sure they are not froze over preventing water through. Also make sure the Water Filter is less then 6 months old, a old filter can prevent enough water pressure for the water to be sent to the ice maker. You can test the Water Valve with a Multimeter. Set your multitester to the R X 1 ohms setting to test for continuity. Place each of the multitester's leads on a terminal. Your multitester should display a reading between 200 and 500 ohms. Closely examine your water inlet valve. The exact ohm resistance rating you should test for may be marked on the valve. If everything comes back good, the Ice Maker will need to be replaced. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
There is a picture of orange drops of water on our water dispenser. What does that mean?
For model number PFSS9PKYASS
Hi Lauren, thank you for your question. You may need to change your water filter. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
Joseph
April 10, 2023
On the automatic icemaker, what does the "Test Switch" button do and how does it work. Our icemaker will not take in water and make cubes. We can get water from the dispenser.
Thanks.
For model number PFSS9PKYASS
Hi Joseph, thank you for reaching out. Based on our research, the test button on the ice maker is for resetting the ice maker. You may hold this button down for a few seconds and it will cause the ice maker to dump the ice, and refill it with water. If the ice maker is not taking in the water, then you may need to replace the ice maker assembly, part number PS2577893. Before replacing it, we suggest checking the water tubes to ensure there is no clogging in them. We hope this sorts out your problem!
Unscrew old filter and remove(counterclockwise). Line up arrow on new filter with arrow on connection housing. Turn clockwise till resistance met. Do not overtighten. Follow directions. Simple.
Until I figured out that the Metal cover on the divider door had to be removed (pried out) giving access to the hidden hinges. After that the hinges could be removed and replaced.Great with giving phone thou.