PFCS1NFXCSS General Electric Refrigerator - Instructions

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

no brainer,watched the video,worst thing was to thaw the freezer,it was realy frosted,works like new,very happy thank you.

I can't tell you how luck I feel after finding your website I ordered the temperature sensor after watching one of your videos on-line and the repair went just as on the video. I pulled the "bad" sensor out, and replaced it with the new one. Keep in mind that this is the first time I ever touch an appliance, needless to say I'm feeling pretty good about that! All in all it took me about 20 minutes to complete my repair and it now has been about 4 days and the refrigerator is working like new again!

Remove the shelves then remove the back by removing the two screws at the top of the panel. Locate the temperature sensor on top of the coil. Cut the wires and replace with the new one. Use wire nuts and electrical tape to reconnect the wires.

The problem began when freezer thawed and could not keep food frozen. Initially, I thought the issue was the defrost heater (because I had seen similar symptoms previously and resolved the issue with a new defrost heater)and I replaced that part with a spare that I had puchased previously. The issue was still unresolved and I noticed the evaporator fan was not running in the freezer because it would not turn on when I closed the door. I checked to make sure I could hear the compressor working (and it was)and concluded that the evaporator fan motor was not running. I ordered the part and found a YouTube DIY video on how to replace it. While I was at work, my fiancee took it upon herself to watch the installation video and install the new evaporator fan motor and all is well.

replaced the icemaker inlet valve. works like a champ now

I decided to replace motor and fan, having previously altered/trimmed the fan which stopped the howling but caused a vibration. Unplug from mains. Clear out two top shelves in freezer. Remove light cover. Remove two screws(1/4 driver)at top of steel panel in rear of compartment and let it drop. Remove two screws above light. Pry up section above light/fan housing to access two screws retaining the light/fan assembly, loosen screws sufficiently so that assembly can be lifted and removed. Disconnect wiring plug by pinching in the sides of the plug and pulling out. Pull fan off motor shaft. Remove two screws clamping motor. Cut cable tie and molded wiring grommet to free wiring. The existing light wires can be removed from the old plug by carefully cutting around the old plug to free the pins and then pushing the pins into the new plug. Reverse procedure to assemble.

replace sensor in refriger.

Removed mother board and replaced. Working fine now

followed part select video instructions

i followed a video that was on your site, the video couldn't have been easier to follow it was step by step and very easy to follow, i replaced the evaporator fan motor and everything is working fine, i did notice that the evaporator coil was frozen pretty bad when i removed the back freezer panel i am going to check it again in a couple of weeks to make sure i don't have a defrosting problem as of now everything is fine i am hoping it was just the bad fan motor causing the coil to freeze up because of no air movement over the coil

followed you online video and it was easy and simple repair only took about an hour frig is back quiet and working fine thanks also parts come fast

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

it was easy the only thing was i had to cut old harness to remove 2 wires that went to coil that had to go back in the new harness other then that a peice of cake.