PDWT302V50II General Electric Dishwasher - Instructions

Opened dishwasher after it completed a wash cycle. Found the rinse dispenser cap had come off during the wash and melted on the heating coil at the bottom of the machine. Pulled cap off of coil, made sure coil was not disturbed. Looked in various sites for cap. Finally found this site where I didn't need to order the whole mechanism and could order just the cap. Received the cap, screwed into the dispenser, fixed. The only problem I had was that there were two possible caps so I picked the one that was the same color as the original one. Project completed. Thanks

Ordered part online, arrived two days later. Removed and replaced dispenser with new unit. Easy job. Dishwasher works like new.

took apart lower spray wand cleaned filter noticed sump basket tube to be decaying flaking apart sump filled with white grit and flakes had been using Cascade all it's life and had no problems till new formulation of Cascade and then had all the problems. Steps to replace sump basket #1 turn water and power off to dishwasher #2 disconnect water line, drain line, and power cord #3 remove dishwasher from cabinet #4 open door and remove both upper and lower baskets (upper basket comes off when you remove the end plastic pieces(push in the button like piece from the side of the track and remove the end piece on both sides and the rack comes out)) #5 pull up and off lower spray wand be sure you remove the stainless steel washer that they use as a bearing for the wand #6 remove round white nylon nut(fine filter nut) that holds screen assemble in #7 remove screen by pulling straight up this also has a tube that inserts into the sump #8 remove the main conduit assemble from the pump #9 remove the upper spray wand (center screw)unit should come off #10 remove main conduit from dishwasher #11 remove sump screen cover (you may have to squeeze together to remove #12 remove inner sump basket ( it is held in place by 2 molded catches on either sides of the basket you will have to release these or just pry the side together and lift out) #13 sump cover and basket may break in removal but not expensive parts and will have to be remove before lower dishwasher bottom (perforated screen) can be removed #14 a shop vac to suck out remainder of water from sump may be helpful since now you will have to close door and turn unit upside down #15 lower sump connects to the dishwasher housing by a screw clamp, along with a sensor connection, to the pump intake, and the discharge pump #16 after all clamps are removed and the sensor removed pull the sump off the dishwasher body (note a oval ring inside the sump this mush be retained since it does not come with the new sump #17 assemble in reverse order (NOTE BE SURE TO INSTALL THE OVAL WASHER IN SUMP PRIOR TO PUTTING SUMP BACK ON DISHWASHER BODY and MAKE SURE YOU PUT LOWER DISHWASHER SCREEN (YEA THAT PERFERATED STAINLESS STEEL BOTTOM ON BEFORE YOU PUT THE SUMP SCREEN IN) Also clean and flush the fine screen from any food it may have trapped, the wands flush to make sure your spray ports are clear and not plugged. I replace the sump with a new sump screen and sump cover since they are a little different in the new design from the old. I also dumped Cascade and switched to Finish dishwashing soap it still has some phosphates in it which helps cleaning immensely

Removed the holding screws around the edges; removed and replaced the soap container; reconnected the electrical leads, and done... Very simple fix. But it does get a little tricky since the door is spring loaded. NOTE: THERE ARE SCREWS AT THE BOTTOM THAT IS NOT OBVIOUS.

simply removed broken valve and replaced with new valve, easy peasy. shipping was GREAT, Overnight. all in all a easy fix.

look at neww part first then r&r

Came home for lunch to discover the kitchen rug soaked and the dishes I had started when I left that morning unclean. Not sure what happened, pushed start again and immediately found water flowing out from under the machine. pulled the machine out and discovered that mice had chewed through the pliable vinyl sump tank. found the part number in my owners manual and google turned it up on Part Select. this was on Saturday and I had the part Tuesday. very satisfied

Water was leaking from under refer next to installed under counter dishwasher. Once determined to be dishwasher not refer I removed dishwasher toe place was able to see dripping inlet solenoid valve. I had to disconnect 11V power, shut off inlet water, disconnect inlet water house and remove dishwasher from under counter. Once dishwasher was in center of kitchen I flipped it upside down and removed the electric solenoid inlet valve. Removing the valve took one wrench to remove inlet hose then two wrenches to remove 90 degree brass fitting and another to hold solenoid. I used a nut drive to remove two screws that released the solenoid from the dishwasher frame. I used teflon tape to reattached the 90 degree brass fitting and inlet hose.

remove front lower cover, 2 philips screws, turn off water supply under kitchen sink to dish washer, turn off power to dish washer, remove water supply line to valve, remove power to valve, clip ons, remove two 5/16" screws holding valve on, turn valve gently to access clip holding washer supply hose, push clip up hose and hold hose while pulling valve off. re-install in reverse order, a flash light helps.

Shut off water, disconnect drain line from disposer. Remove dishwasher from wall and remove water feed line. Unplug or disconnect power to unit. Remove upper and lower dish racks as well as lower water sprayer bar, and filters. Lay dishwasher down on backside (make sure to catch water with bowl). Disconnect pump connector with nut driver and replace. Stand dishwasher back up and reverse removal process

Twisted new one in place of old. Disappointed that there was a melting issue at all. Need to investigate problem.

very happy with the product and fast shipping. removed kick plate from dishwasher, inlet valve was on the front left bottom slid out dishwasher removed two screws and disconnected water line,and installed new inlet valve,very simple job if your somewhat handy,make sure you use thred sealant on water line when re installing

Had purchased SPRING DOOR, CABLE ASM, and HINGE CABLE PULLEY prior to starting repair, as I did not know which piece had failed. Cable assembly was the culprit. SPRING is heavy duty steel, HINGE CABLE PULLEY is nylon, and CABLE ASM (assembly) is braided steel with a steel plate at one end that ties into spring and an inadequate nylon piece that ties into the steel hook on the door. The nylon piece failed through tearing open. REPAIR STEPS: 1. Removed bottom cover plate at front. Two hex head nuts. Nut driver works best but Phillips head screw slots are on nuts. 2. Removed dime-sized cover plates located on either side of main unit where door seals when it is closed. Used Phillips head screwdriver to remove screws that are screwed into cabinets flanking dishwasher. Magnetic tip will help keep you from losing these between dishwasher and cabinet as they are too short to project through the access hole when fully unscrewed. 3. Lowered appliance feet using adjustable pliers. Slip wrench would probably work but six-sided appliance feet are slippery. 4. Loosened drain hose clamp from disposal and removed drain hose. 5. Shut off water line to dishwasher (under sink) and disconnected water line with slip wrench. Steps 4 and 5 were done to give me the slack I needed to pull dishwasher out from cavity far enough to access the side where the repairs were to be made. You may or may not need to do that--try pulling dishwasher out first and see how far it will go. 6. Looked at the problem, which was failed cable assembly. 7. Removed nylon Hinge Cable Pullley with nut driver. This allows cable removal. 8. Put cable back into place (loose) and then replaced Hinge Cable Pulley. 9. Reattached cable to spring on back end and door hook on front end. 10. Pushed dishwasher back into position. 11. Raised appliance feet to proper height. 12. Reinstalled side screws that hold dishwasher against cabinetry. 13. Replaced small screw cover plates. 14. Reattached drain line to disposal. 15. Reattached water line. 16. Turned water on and checked for leaks. 17. Reattached bottom cover plate to front of dishwasher.

Just have a good look at how the original is installed before removing, then clean the area. The new one was a breeze to install, just line it up and pop it in.

I unscrewed the screws in the door of the dishwasher. Then pulled the inside part of the door up and unscrewed the 6 screws that held the dispenser. I am not sure the correct name of the part but it is on the backside of the dispenser and is red and it is where the wires connect to it, that was probably the most difficult part, disconnecting the plastic covers from the old dispenser. I used a butter knife to pop it out and then was able to get a better grip to pull them off. I pushed the wires on the new red thing and then put the new dispenser in place. You have to make sure that the dispenser is in the right spot and the brace on the underside of the inside part of the door, is in the correct place, otherwise, you will have a leak. Which is what happened to me. I just unscrewed and opened it again and screwed the screws tighter and it was fine.