PDWF680R10SS General Electric Dishwasher - Instructions

After determining that the leak was coming from the sump connector, I had to completely remove the unit from the counter. After removing all the parts in the wash cabinet (wash arms,conduit,fine,course and sump filters),the sump connector nut was revealed which I loosened, but did not remove, with a channel lock plier. The unit was then placed up-side down where I then loosened all the worm clamps that attached the drain motor,pump,and turbidity sensor to the sump and sump connector.then I removed the brackets that braced the pump to the washer body and removed the pump.at this point,you should be able to remove the drain motor and turbidity sensor from the sump and remove the sump from the washer. You should also be able to remove the connector as well.Both these items are made of some type of rubber which seems to deteriorate from the soap which was caked all over them in my case. Just reverse the above process to re-install everthing. I didn't find this job terribly difficult and it was certainly better than spending hundreds replacing the unit.

Found numerous references on internet that most likely cause was due to a fouled or plugged suction screen. I unscrewed anchor tabs on top securing the dishwasher to the countertop, slightly lowered the front screw legs, turned off circuit breaker at the electrical panel, checked to verify the power was off, removed the small electrical cover under the dishwasher and disconnected the 3 wire nuts, pulled the dishwasher partially out, then disconnected the small corrugated drain hose from the discharge pump under the washer being careful to collect small amount of drain water in a bowl. Finally, carefully pulled dishwasher out from under the countertop leaving the hot water supply hose connected. Tipped washer over onto back (the frame rails are rounded in the back to help facilitate this). Had to unscrew the hose clamps to remove the rubber sump. Then stood the dishwasher back up to disassemble the plastic screen parts from inside the dishwasher. The screen was in fact plugged with white slimy deposits that when dried became chalk like. During cleaning out the white caked on deposits in the rubber sump, I accidentally pushed my screwdriver through a rubber vent stand tube and this is why I had to buy a new rubber sump. The sump rubber material appeared to be partially deteriorated which is why my screwdriver passed through it. Reassembly wasn't very easy. It was difficult to get the rubber sump boot over the plastic flange on the bottom of the tub. It helped to remove the metal hose clamp completely and to have someone hold the dishwasher in place lying on its back while I pushed and prodded to get the rubber seal over the oval flange. Once on, everything went back together easily in reverse order. It probably took me a total of 6 to 8 hours of real working time. But taking into account that I only worked for short periods of time on evenings after work and the fact I had to lug around my extra 70 lbs of gut, the constant laying down and getting back up, the 4 day wait for the new rubber sump to arrive, and my near senior citizen age stretched this 8 hours of work out to a two week home repair project. BUT, I was successful and everything is back to perfect working order. Thank you Partselect.com for having the sump in stock and to my door in only 4 days!

Replaced the part by taking off the srews on the inside of the dishwasher door (all of them)to get to the backside of the soap dispenser. Remove an electrical connector by pulling (had to pull off using pliers as it was really on there). Then a couple of screws hold to to the inside of the door. Pretty straight forward.

I had a small leak from under the dishwasher which turned out to be a tiny hole in the Pump Connector. With the power off I pulled the dishwasher out of the cabinet and disconnected the water and drain lines to give me more room. I put the dishwasher on its back to have access to the pump assembly. A couple of nut drivers and the pump connector is accessible. Replaced the pump connector and over tightened it "Crack"... had to replace the Main Conduit connector ($50). I was able to turn a simple $20 repair into a $70 repair. Now that's talent!

On the Model PDW9880, there are about 14 screws to be removed. I used a large Phillips driver and a pair of needle nose pliers. You cannot use a cordless drill driver for about 10 of the screws unless you have a long bit, as the 10 screws are so close to the body of the dishwasher door that the chuck of the drill will not clear. At the top of the door there are two screws on either side of the latch. The two screws are attached to white plastic blocks that serve as a lip to hold the outer door to the liner. It took a little wrestling with the two plastic blocks to slide them out from under the lip, releasing the outer door. Be sure not to let the outer door drop away, as it will tug on the ribbon cables that connect the display to the dishwasher. Keep a towel or sponge handy to keep the
dishwasher handle from resting on the tile floor. There were 4 electrical connections, including two ribbon cables, both of which just pulled out. I needed a needle nose pliers to remove the 2 spade connectors from the detergent dispenser solenoid, in order to pull on the connector, not tug on the wire. The entire repair is actually pretty straightforward and easy. It took 40 minutes, doing it slowly and carefully. But please don't tell anyone that it is easy, because my wife thinks it was an extremely complex repair, involving the risk of high voltage electricity.

The replacement part fits different makes and models, and does not have any brand identification, other than the Cascade logo cast into the front. Other than that, it appears to be identical to the original. Note: The
soap cup does not open for several minutes in the cycle, so don’t waste time or frustrate yourself (as I did) by checking the dispenser during the first 10 minutes of the cycle. Incidentally, although the company is in Canada, my part shipped from Central California (Fresno) and arrived in the Los Angeles area the next business day.

took apart lower spray wand cleaned filter noticed sump basket tube to be decaying flaking apart sump filled with white grit and flakes had been using Cascade all it's life and had no problems till new formulation of Cascade and then had all the problems. Steps to replace sump basket #1 turn water and power off to dishwasher #2 disconnect water line, drain line, and power cord #3 remove dishwasher from cabinet #4 open door and remove both upper and lower baskets (upper basket comes off when you remove the end plastic pieces(push in the button like piece from the side of the track and remove the end piece on both sides and the rack comes out)) #5 pull up and off lower spray wand be sure you remove the stainless steel washer that they use as a bearing for the wand #6 remove round white nylon nut(fine filter nut) that holds screen assemble in #7 remove screen by pulling straight up this also has a tube that inserts into the sump #8 remove the main conduit assemble from the pump #9 remove the upper spray wand (center screw)unit should come off #10 remove main conduit from dishwasher #11 remove sump screen cover (you may have to squeeze together to remove #12 remove inner sump basket ( it is held in place by 2 molded catches on either sides of the basket you will have to release these or just pry the side together and lift out) #13 sump cover and basket may break in removal but not expensive parts and will have to be remove before lower dishwasher bottom (perforated screen) can be removed #14 a shop vac to suck out remainder of water from sump may be helpful since now you will have to close door and turn unit upside down #15 lower sump connects to the dishwasher housing by a screw clamp, along with a sensor connection, to the pump intake, and the discharge pump #16 after all clamps are removed and the sensor removed pull the sump off the dishwasher body (note a oval ring inside the sump this mush be retained since it does not come with the new sump #17 assemble in reverse order (NOTE BE SURE TO INSTALL THE OVAL WASHER IN SUMP PRIOR TO PUTTING SUMP BACK ON DISHWASHER BODY and MAKE SURE YOU PUT LOWER DISHWASHER SCREEN (YEA THAT PERFERATED STAINLESS STEEL BOTTOM ON BEFORE YOU PUT THE SUMP SCREEN IN) Also clean and flush the fine screen from any food it may have trapped, the wands flush to make sure your spray ports are clear and not plugged. I replace the sump with a new sump screen and sump cover since they are a little different in the new design from the old. I also dumped Cascade and switched to Finish dishwashing soap it still has some phosphates in it which helps cleaning immensely

removed front panel and replaced new part. Timer did not work because plug kept disconnecting. Called GE service and watched him remove panel without removing control panel. Plug for timer can be installed easily and front panel replaced without disturbing cable.

Replaced wax motor and soap dispenser (all one piece). Only problem was the plastic seal on the very bottom of door had come unseated, and therefore was leaking. You need to check that it is snapped all the way in, and then the leak ceased. Took me a few tries, which made a ten minute repair into an hour long one.

This is a somewhat difficult task in that the dishwasher had to be pulled out of the cabinet which required the water inlet hose to be removed (and water to the hose to be shut off). Once the dishwasher was free of the cabinet it had to be flipped over to reach the water inlet valve. Once the valve was replaced go in reverse to reinstall the dishwasher. Worked fine after I got everything installed; no leaks.

Simply took out the broken rack and inserted the new one.

Installed new rack assembly and it works fine. Thanks

I took the old one out and replaced it with the new one. It did take both hands as I had to open the dishwasher door while the other hand held the basket. :D

After reading other customer responses I decided to attempt the repair myself. After pulling out dishwasher I turned it on it's side and prodeeded to remove the 3 screws holding it in place. FIFTEEN minutes later I pushed it back into position and it has performed like new for the past month. Comparing parts and service I saved about $200.00 on this self repair. I would not hesitate to undertake another repair after my experience.

Remove the door panel screws on the inside door frame. You only need to remove as many as needed to remove the larger bottom panel. The other screws will remove the upper button panel and this is not necassary. Unplug the Detergent Dispenser (it may take some force, and unscrew the dispencer. Replace with the new one, screw back in place, and reattatch the plug. Now replace the door panel and screw it back in place. This is all very simple. The only problem I encountered was that the only dispenser had built up so much detergent residue around its base, that it had distorted the plastic around it. This caused the new dispense to not sit flush all the way around, and the dishwasher leaked into the door on its first cycle. Simply filling the gap with 100% silicon caulk has fixed the problem. Washes like new.

removed inside door panel to access the pump; then replaced with new pump