PDF22MFSW General Electric Refrigerator - Instructions

Replaced Temperature Sensor and now it is getting cold.

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!

with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.

Of course I had to order the filter and upon receiving it I installed the new one in about a couple of minutes. Even though my fridge doesn’t have a water dispenser it does make ice. Removed all the old ice from tray and disposed of it cause it was getting a bad taste to it. I let the tray fill up with ice once and disposed of the ice. After it filled up a second time I tasted the ice and had a very good clean taste. And my lesson is I need to replace filter at least once a year I think would be sufficient. That’s all there is to it, simple !!!

It was way to ez to install only a couple of minutes that's it

took a little more effort than the video show to remove old module and replace new. Works fine now.

Started with a visual inspection.
Turned off water.
Removed old valve.
Bent bracket to facilitate installation.
Installed.
Hooked up.
Tested.
Works as advertised.....

My Son removed two screws, electric plug and two (2) compresion nuts. He had to bend the bracket to fit, then replace it, in reverse order except the filler tube on the new valve was of a "stabb-in" type. Job was a piece of cake and this small project, solved all our problems with the Ice maker.

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

1st - checked water supply - old valve in water line was closed with sediment.
2nd - replaced water line valve and reconnected copper tubing about 1 hour
3rd. removed single outlet valve and installed the new part - about 15 minutes

Everything went well and was very easy.
Unfortunately, the ice maker still does not work.
Still trying to understand what is wrong.

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

Unplug electrical power to refrigerator. Disconnected electrical power to water valve, Disconnected water inlet and out let lines from valve. Remove screw holding valve on refrigerator, removed and replaced water valve with screw. Connected inlet and outlet water lines, turned on water and checked for leaks. Connected electrical power to water valve, plug in electrical power to the refrogerator. Ice maker tray fill, made ice.