PDCS1NCZALSS General Electric Refrigerator - Instructions

Very limited working space in this model. Must remove grill and disconnect elect connector on motor. One additiional tool suggested: Extendable rod with magnet on end because you will most likely drop something. First, remove two screws holding motor to metal strap. Tool must be inserted between blades of fan in order to get to the screws and this is the hard part. Fan and motor are removed as one assy and this takes some manuvering. Might have to remove front screw on metal strap to gain more room. I did not attempt to remove fan shroud. My fan was attached to the motor shaft with a metal clip. Spray a good lubricant such as PB Blaster on the shaft, wait a few minutes and press it or tap it out gently. Save misc parts on old motor for reassembly. Your set up may be different so check out everything before starting.

I looked up appliance on internet,diagram only showed the inlet valve and ice maker in schematic.I ck'd to see if water was getting to valve(it was)but wasn't getting to ice maker,thus I replaced the valve and it solved the problem.

as per video

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.

There were only 3parts listed to check omed out the defrost heater and thermostat ....thermistor checked bad ordered replacement took less than 2 minutes to replace after I defrosted it again runs fine

easy pry out, disconnect wiring, connect on new switch and press in switch.

My son replaced both temperature sensors and the fridge works great now!!! Like brand new again!!!!

no brainer,watched the video,worst thing was to thaw the freezer,it was realy frosted,works like new,very happy thank you.

Located temperature sensor on condenser in the freezer section( as per instructional video ). Cut off bad sensor with wire cutter then soldered on the new sensor and sealed with electrical shrink wrap.

as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved

I identified the noise was coming from the coils / and the fan. Cleaning the fan helped reduce the noise a bit but it still kept recurring. I ordered the part, which was really easy using the diagram on the website. The instructions and the video were really helpful and was able to remove the old motor and replace it with the new one with relative ease. While there I cleaned the fan blade and vacuumed the surrounding area. This whole repair went quite smoothly and has given me the confidence to take on other repairs before calling out the repairman.

The repair is a snap, you can watch the video and it will put you on the right path. My story is more about the service that Part Select gave me. I used a small box fan on low as a temporary fix. My model number was worn off from the box wine we store in that particular place. So I ordered the part based on looks, well it was wrong. Called Part Select and we talked, the nice lady on the other end said OH it must be this fan motor. Send us back that one, and I'll get this out too you. I'll credit your account for $7.99, and it cost me $8.99 to ship back the wrong part. Wow, the next day I received the new motor. They sent it overnight! I thought it would be 5-6 days! Unbelievable. I will use this company for any, and all my repairs.

changed sensors did not repair problem,replaced damper with mechanical damper fixed problem.

took out shelves and removed the back plate my removing 2 screws with a nutdriver.removed the old defrost timer and defrost heater which was really easy.then installed the new ones.the video i watched on the website was really helpfull.