Models > PCGB980ZEJ1SS > Instructions

PCGB980ZEJ1SS General Electric Range - Instructions

All Instructions for the PCGB980ZEJ1SS
1 - 14 of 14
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Grate to replace griddle
Remove griddle insert grate
Parts Used:
CENTRAL GRATE
  • Barbara from LOUISVILLE, KY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
10 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing grate foot / bumper
Put in a new foot / bumper. That's it.
Parts Used:
Burner Grate Foot
  • Irene H from HENRICO, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
9 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Warped burner
Set the burner in place
Parts Used:
Range Surface Burner Head Outer Burner Cap
  • Ray from LEESVILLE, SC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original burner cap was chipping; must have been dropped somewhere along the line.
New burner cap replaced old; just placed over burner; no tools required.

One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
Parts Used:
Burner Cap - 15K
  • Mitzi from Briarcliff Manor, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
8 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One burner would not light from spark. All other burners lite with spark.
First I checked that the wire and sparker was working by switching the wires on top of the range. I did this by pulling out the sparker switching it from the back working burner on the same side. The same burner would not light so I knew it was not the sparker.

Then watch a bunch of videos and found this gal to be the most helpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY

I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.

All burners have been working perfectly since the fix.
Parts Used:
Spark Module
  • Thomas from DEARBORN, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Large burner cap finish was damaged
Just lifted old burner off with my fingers and replaced with the new one. What needs to be focused on here is the fact that Part Select has such a complete line of parts rather than the difficulty in the install.
Parts Used:
Burner Cap - 15K
  • Richard B from CLARKSBORO, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original Grates and Reversible needed replacing. The replacements were a perfect fit.
Did a search and found PartsSelect.
Inserted the model number of the GE Profile Gas Range.
Located the the needed parts, and added to the 'shopping' cart.
Then purchased, then waited for delivery.
Parts Used:
REVERSIBLE GRIDDLE GRATE Assembly
  • Karen from CEDAR RAPIDS, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wrong parts
Your diagram on your website says lower oven is incorrect everything on there is upper oven I ordered the wrong part because your diagrams are all wrong OK
Parts Used:
BAKE DEFLECTOR UC
  • AMON from MARYSVILLE, CA
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    30 - 60 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the griddle was scratch up
just replace the griddle with the grate.
Parts Used:
CENTRAL GRATE
  • Betty from PHILADELPHIA, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed center burner grate
Very easy. Unpack and place on stove. Everything fit perfectly.
Parts Used:
CENTRAL GRATE
  • Dianne from HAMPTON, NH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
None
Replace existing grate with a griddle. Lift off existing grate, place griddle in its place
Parts Used:
REVERSIBLE GRIDDLE
  • Walt from WATSON, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Food ran over the burner and damaged it.It was easy to place it back inII
It only required placing the new burner in the proper location.
Parts Used:
Burner Cap - Black - Medium - 9500 BTU
  • Alan from PASADENA, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Part does not look like the part that needs to be replaced
I have no clue what wire goes where because there is no thing to refer to or instructions of any kind . I have not been able to install the part.
Parts Used:
Spark Module
  • P from FULLERTON, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..
Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre
Parts Used:
BRACKET ANTI-TIP Assembly
  • Greg from Ft. Washington, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the PCGB980ZEJ1SS
1 - 14 of 14