PCF25MGWB General Electric Refrigerator - Instructions

It was very simple! I assessed the situation and gathered my tools for the job. I used a flat head screwdriver, pliers, and electrical tape. I used the flat head screwdriver to release the switch from its location, the pliers to take the electrical terminations apart. I taped the wires individual so that I would not loose them in the door, also not to short them out. I then unpackaged the new switch to install. Pulled the tape off one of the of the terminals while holding the wire, and attached it to the new switchs terminal post. Did the same with the other wire, then snapped the new switch back into place. Immediately had results. I opened and closed the door a few times in amazement that something so annoying such as a light in your fridge could be so easy to fix. Most of all, having a business to rely on to find the part and deliver in a timely fashion. Thank you Partselect.com, you were outstanding!!!

This is the second or third time this cup has broken. Maybe we use more crushed ice than the average family, but you would think this part could be more durable. Anyway, I digress. This is about the repair. Four screws removed around bottom of tray, one screw removed for some bar that mechanically opens a door to allow ice to fall out of the tray, and two butter knives used to release tabs around the screw components... and we were done.

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

I searched YouTube for the problem and was quickly taken to several videos that detailed to required actions. This encouraged me to proceed, so I took the back cover off and found the water valve leaking. I then googled the make and model of the frig and found the part. The YouTube videos provided all of the details needed to determine the problem and replace the faulty part. Once the part arrived, I was able to install the new one in a few minutes. Operation returned to the water dispenser and the leak was gone. Total cost of the repair was $56 and took about 1.5 hours to remove the original part, order the replacement and install it when it came. Perfect!

Removed the ice maker from the freezer. Unscrewed the outer cover/base of the ice maker. Unscrewed the long lever that opens the ice chute. This freed up the feeder coil enough to pull it out enough to replace the cup drive. Once I replaced the cup drive, I laid it back down into the ice maker bin, reattached all the screws and it worked! The old cup drive had a tine broken off which would not allow the feeder coil to turn. It seems like a weak part and I anticipate I may have to replace it again in a few years.

Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed

I tried to quite the noisey evap motor with special liquid motor grease from Radio Shack. It did not work, so I ordered the evap motor. My freezer motor was wired slightly different than the motor I received. The replacement motor had a male plug attached to the four wires, the original motor was different, so I cut the wires and spliced them into the original freezer wires (colors were the same). Remounted motor. Works great, and no more groaning motor
Peter

Removed ice bucket and observed the plastic drive bushing for the auger had the drive dog broken off. I removed the four screws on outer shell for the ice bucket, removed it and found the auger had key stoned a hole in the ice tray housing. At that point I decided to replace the ice bucket and auger assy. The new one works fine.

I removed the ice from the tray, took out the four screws from the tray, pulled up the metal spiral took out the old drive cup, replaced with the new one, replaced the screws and put the tray back in the freezer. A piece of cake. Thanks for your prompt service and the reviews on how to replace.

Removed three screws holding the evaporator cover. Removed screws holding the evaporator to the back wall of the compartment. Removed the drip pan which was rusted through. Inserted new drip pan. Cut and spliced new tempature sensor and inserted it onto the aluminum block which is attached to the back side of the evaporator. Installed new cover which includes a new fan. GE wanted almost six hundred dollars to do this repair. I paid $180.00 for all the parts, installed them in about an hour and the unit works like new.

1. Removed the back panel of the fridge to get access to the inlet water valve.
2. Removed black poly water line from valve (pull back on white ring where line is attached and pull the line out)
3. Removed the inlet tube from top-back of fridge (where it goes into the ice make). use putty knife to get under the sticky white gasket beneath the black oval housing and pull the tube out form the back of the fridge.
4. Replace the water line with new part taking care to properly seat the line into the the bottom water valve and pushing the water tube into the hole for the ice maker.

Note: Be sure to take off the protective covering from the white - sticky grommet and push to adhere to metal on fridge.

to be safe - use a bit of clear silicone chaulking round the perimeter of the grommet and push to tighly bond the water inlet tube to the fridge.

The reason for this - is that if you do not get a good bond using the white - sticky gormmet alone - you may have the water tube inside the ice maker freeze up.

Also once the new water line is installed be sure to secure the line to the metal back of the fridge - so the line will not move. some fridges come with metal hose clamps to do this - otherwise use duct tape

several times I had to remove the ice maker door solenoid due to it sticking. I ordered a new one from parts select. Problem solved!!!

I removed the 4 screws from the cradel then I wedged the tabs open on the unit and removed the main operating mechanism .Ithen removed the broken parts and reassembled the mechanism I put the unit back together in
reverse order. It works just fine.

I removed the outer plate by sticking a very small screwdriver in the small holes at the bottom of the plate and pulling the plate toward me.
I then removed the 4 screws from the internal plate and pulled the plate toward me.
Then I romoved the 3 screws holding the old solenoid and unplugged it.
Next I put the new solenoid in place and replaced the three screws.
Finally I plugged in the solenoid and replaced the internal and external plates.

Procedure for Replacing the Ice Chute Plate
1. Turn off the power.
2. Snap off the outside trim ring. Use a plastic screwdriver to avoid scratching the cabinet.
3. Locate the three small holes below the control panel facing, just above ice chute. The center hole is not used. With a small, blunt, object (wire – blunted nail) that is slightly smaller than the holes, push up rather firmly up through the outer holes to release front control panel.
4. Remove the three wire connectors from printed circuit board. Firmly pull/pry them straight out of retaining clip. Use caution: Excessive force will break clips.
5. Release the secondary panel by removing four screws (one in each corner).
6. Remove the flap assembly.
7. Clean all accessible areas with 1/10 bleach water to sanitize. Rinse the cleaned area with clear water and thoroughly dry everything before re-assembling the panel.
8. Install the new flap assembly.
9. Re-installed everything in the reverse order and check the functionality.
10. Order a spare ice chute flapper to be ready for the next event.