PB920TP1WW General Electric Range - Instructions

Read the instructions on how to remove the door, found in the owners manual. Once you release the hinge lock latches, the door can be lifted off of the hinge arms.

It is fairly heavy and bulky. I spread a large towel on the kitchen table and placed the door, front side down on the towel.

Remove the 3 nut screws at the bottom of the door and then lift the inner door assembly up about 3" and hold it up temporarily with a medium sized plastic food storage container. This will allow room to access the 4 nut screws (2 on each side) that secure the trim to the door.

The old trim was somewhat difficult to remove because of years of rust and other build up where the front door glass goes behind the trim. Be careful not to damage the glass. I used a putty knife.

The edge of the glass will be soiled so I used a mild abrasive cleaner to remove the rust and grime, and then used a window cleaning spray to clean the glass.

The new piece had to be "fitted" slightly to match the existing screw nut holes but it goes together quickly.

Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Theaded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.

Watched video

Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!

Watched youtube video. Very easy to replace

Performed repair using a video for reference.

Took a picture of the old heating element to make sure that when I replaced the new element the wires were in the exact location as before.

Part WB30T10126 Triple Haliant Element-12 Inch was returned to you under Returns Reference 15682540. Mailed by USPS Tracking #9505 8161 4647 1005 7628 41. According to USPS, it arrived at your location Friday, Jan. 15, 2021 @ 10:49 AM. Please advise. Thank you, William Deal

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

Used the schematic on the website to order part and disassemble/reassemble with new fan motor. Works like new.

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.

I just watched the video that was on the website. It showed in detail how to replace the heating element. After watching it I was able to remove the cooktop, replace the heating element and put it all back together. The only issue I had was getting the cooktop loose but once I did everything else was easy.

Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.

The part was exactly what we needed. However, we didn't find the video online to show how to replace the part until we were almost finished. (https://www.youtube.com/watch?v=ovwcJhfWHXQ) If we had found the video, it would have saved us a lot of time because we undid more of the door than we needed to. Also, the video tells you exactly what size tools to use. However, taking the door more apart allowed us to clean more of the inside of the door. So, watch the video before you start, and also, be prepared to spend time cleaning the insides of the door. Also, when we put the door back together, we accidentally turned the front glass panel of the door upside down and it wasn't noticeable until we had put the door back on the oven. So, we had to take it apart again to fix it. All said, we're very happy with the new part. Thank you PartSelect!

Removed door from range(see manual for instructions). Set door face down on protective cloth material .Remove two top screwws, 3 bottom screws and lift back of door off. Remove two screws on each side of door bottom channel and remove channel. Put in new trim on bottom of glass window and put screws back in. Set back of door on top of front cover and screw two top screws and 3 bottom screws back in. Set door back into range. Lock clips on both hinges.