PAVT144AWW Maytag Washer - Instructions

My washing machine was severely off balance during the spin cycle. It would bang violently against the side and “walk” across the laundry room. I was able to fix this for under $25 dollars of parts from partselect.com and a few hours. I rated the task as easy, but I am somewhat mechanically inclined. Others may find it a bit difficult but I believe anyone except an absolute beginner can do this job.

Fix this problem before significant damage is done to your base! Otherwise the job will take more time and be a LOT more expensive. My base had experienced a little damage but thankfully it did not require replacement. When the snubber wears out, it allows the tub to rub against the base. Metal on metal is never a good thing.

Also I chose to replace the springs, even though it may not have been 100% necessary. You have to take them off anyway and they are inexpensive. It is easy to know when a spring is broken, but not as easy to know when it has lost some of its spring. Just makes sense to me to replace them.

I used the directions below which I found on the internet. They are listed below unedited by me. I have added a few of my own comments below that.

• Remove power and all hoses
• Lift top by inserting putty knife just inside front clips to release
• Remove front and rear panels, 10mm
• Disconnect drain hose from bottom of drum, pliers - spring clip
• Remove 6 springs from bottom of drum using channel lock or spring tool
• Lay on side, remove drive belt by turning large drive pulley and side tension to belt
• Remove water level hose on side of drum, pliers - spring clip
• Remove drum from cabinet by sliding out top. It is not necessary to remove drum from transmission.
• Inspect base plate for damage
• Lay drum on padded surface, upside down
• Remove C clip, drive pulley, being careful to observe order of parts and washers
• Loosen 6 screws holding down old snubber. DO NOT REMOVE SCREWS, THERE IS A VERY STRONG SPRING UNDER THIS PLATE. Loosen screws only enough to get old snubber out.
• Clean dust from area.
• Insert new snubber, keeping it even while tightening screws.
• Reverse other processes above to assemble washer. Replace any broken drum springs. Replace belt if worn.

My tips:

• After you remove the tub you will see a lot of fine white dust in the bottom of the washer. That is from your old worn out snubber. Vaccum it out.

• I didn’t have a spring tool but I found that using a pair of vice grips to remove and replace the springs was easier than using channel locks.

• Technically, I believe the clip is actually called an e-clip. If you have the correct tool for this removing and replacing it will be a lot easier. I did not have the tool. I used an open end wrench that was just the right size to butt up against the two ends of the clip. A light tap with a hammer against the other end of the wrench and it popped right off. I used a pair of needle nose pliers to put it back on.

• Also regarding putting the e-clip back on, at first I could not see the groove that the clip was supposed to slid into. It was below the little plastic piece with the teeth. I used a small flat screw driver inserted into the groove to gently pry it up and had someone gently tap on the plastic piece which pushed it down enough to expose the grove.

• I highly recommend heeding the warning regarding the loosening of the 6 screws holding the snubber. I did not have any trouble with this but there is a 200 lbs spring underneath that you do not want to release. It could injure you and might be hard to put back. Just loosen each screw 1/4 turn at a time until the snubber can be removed.

That's about it. I took me about 4 hours

After pulling the machine away from the wall and turning off the water and unpluging. I simply removed the panel in the back and reached underneath and removed the belt. Took off the hose clamps and removed the three screws holding the pump on. Put the new pump back in place and hooked up the hoses. Then put the belt on for a test run.......all OK put the back on and was done. Whole job about twenty minutes. Saved over two hundred dollars doing this myself. Very simple repair.

tip washer up on wooden blocks.remove drive belt.remove "E" clip from tub drive pulley and remove all the parts.Install new parts in kit as per instructions.machine works great!

First I took the front shield off, then I took the motor off.

I was able to get the belt off easily but the belt was fine. I changed the snubber easily also. But that wasn't the problem. I went through all the parts that are easy enough to change without a mechanic but turned out it was something inside the innerbasket and we had to junk the washer and it was only 4 yrs old.

just took the front off and then took the old motor off and switched over about 2 parts from the old to the new and then put the new part on and then placed the front back on and it was ready to go

Read DIY review from William, Middleton, OH on 01-15-08. Tip on how to relieve spring pressure on brake assembly worked like a dream (3ea 10-24X2 bolts/machine screws). Replaced brake and machine works like new and was an inexpensive fix. Once the shell/housing is off the machine, tub can be turned upside down and the base doesn't need to be removed. White powder under machine was a plastic wear ring that tells you when your brake rotor needs to be changed. Brake rotor still had lining but was much thinner than replacement part. Note* Use putty knife to push in clips on front to release the top lid section.

1.Removed the back plate from the control panel. 2.Pulled out on the plastic pin (behind the timer) with needle nose pliers in order to release the timer knob. 3.Removed wiring plug and uncliped timer. 4.Installed new timer.

Removed the top cover plate. Some difficulty in getting the cycle knob and skirt off. The whole assembly came out with the cover plate. Removed the screw that held the timer in place, disconnected the electrical connection, inserted the new timer, put the screw in and reconnected the electrical, screwed the top cover plate back on, put on the new skirt and knob, and that was it. Works just fine, and saved me calling a repairman to do it. Who knows how much that would have been!

i took off the old belt and i took off the motor pulley with the pliers and srewdriver. i put the new pulley in with my hand and gave it a hit with the palm until it snap in and then i put the belt on by rotating the main pulley on tub till the belt was pulley on.

I removed the part that was still attached to the washer and installed the new flume. It took less than five minutes and a repair that would have cost over $85 cost less than $10 and I am no plumber!

After replacing the tub to pump hose, I adjusted the feet on the washer. Apparently, the main pulley sits so low on these washers that it ground into the floor and stripped out the thrust bearing. I ordered the new thrust bearing clip and put it in the evening I received it. The instructions it came with were very helpful and it was simple to reassemble. Up until the last piece - the retaining clip. The majority of the repair time was spent replacing that clip. If there is a tool that makes the job easier, I didn't have it. I finally got it on with two flathead screwdrivers prying the shaft out while I wedged one corner of the clip in the groove.

first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy

I removed the plate at lower left corner on rear of washer 3 screws and it pops right off after that there are 2 clamps on the hoses attached to the pump I removed those with pliers then I removed the 3 screws holding the pump to the bottom of the washer then pulled the pump through the hole and replaced it with the new pump installed all the screws then layed washer on its side and replaced the belt set it up pluged it in and no more noise sounds better than new. Thank you Part Select for making it an easy painless task to get the parts I needed.

Removed the screw from the side of the lid of the washer. Took off the old Lid Switch Actuator and screwed in the new one. Took a little elbow grease because the old screw was tight but no longer than 15 minutes tops.