P2S975SEM2SS General Electric Range - Instructions

Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete

First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.

Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.

Turned off power to range, slid range out from counter, removed convection fan cover, removed convection fan blade, removed back of range panel over convection motor, removed motor, put in new motor, put range panel back on, put new fan blade on front of motor, replaced fan cover, turned power on. No more clunking noise from motor.

Shut the power off at the electric box.Disconnected coil from roof clips.Pulled wire connection from back wall. Disconnected wire clips, connected new unit.Clipped to roof and turned on" Working fine".

The actual repair was relatively easy but access to the area in the oven made it a little difficult. Just unscrew 5 screws with a nut driver, unplug the old element, plug in the new element and reinstall the 5 screws. The only thing that made this repair difficult was being able to reach the connectors where you plug in the new element. They are loose wire connectors that don't reach very far out of the element receptacle. It was difficult to hold the end of the connector and plug in the new element because the oven door is in your way. Maybe it is easier if you take the oven door off first?

Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.

Replaced old burner element with new, easy

Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."

Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.

Ordered by phone parts & very pleased with all of transaction.

I was attempting to replace the broiler element on the oven, but I discovered that the wiring may be the actual problem. I suggest before you order parts for a broiler repair, that you test the wires to ensure that you have continuity. I will have to trace the wires back to the source (the other element works fine) and see if I can find the problem with the current. I will keep the broiler element I ordered until I can confirm that the old element works.

Turned off the circuit breaker. Removed 5 screws. Unplugged the heating element and then plugged in the new one and replaced the 5 screws. Very simple.

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .

Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.