This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
This part changes the transmission from agitation to spin mode. This actuator is for washers.
Actuator shifts the splutch and monitors the position of the splutch.
These parts are the replacement suspension rod supports for your washer. They are made of plastic and are approximately 1 ½ inches in diameter. This package will come with an 8-piece set of suspension...
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, you...
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time
$190.78
In Stock
Questions And Answers for NTW4600YQ1
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jean
December 3, 2019
Lorsque l essorrage elle très bruyante
For model number NTW4600YQ1
Hello Jean and thanks for writing.
It sounds like a faulty check drive pulley PS10057144 replace if needed. It is also recommended to check your belt PS11747978 for proper function.
We hope this helps. Please contact us anytime.
Bonjour Jean et merci d'avoir écrit.
Cela ressemble à une vérification défectueuse de la poulie motrice PS10057144 à remplacer si nécessaire. Il est également recommandé de vérifier le fonctionnement de votre ceinture PS11747978.
Nous espérons que cela aide. S'il vous plaît contactez-nous à tout moment.
Where does the 4 suspension rods springs go on this model I have bought the rod kit but the 4 small springs I am unable to locate them or find an illustration reference !!??
For model number NTW4600YQ1
Hello Terry, thank you for writing. The Suspension Rod Kit PS11703290 is located on the schematic entitled, Basket and Tub parts item #14. We have a video for you to access. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
Why would this level machine walk across the floor during the start of spin cycle ?
For model number NTW4600YQ1
Hello, Thank you for your question. You will need to check the suspension rod kit and supports. Those typically what cause the appliance to become off balance and move around. We hope this helps.
Was this helpful?
Thank you for voting!
Jack
February 8, 2020
Should there be springs or straps at top of tub running to corners to control wobbling?
For model number NTW4600YQ1
Hi Jack. They are springs. You can see the installation video and kit below. Thank you for your question and good luck with your repair.
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer failed which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this information the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
