NDG2330AWW Amana Dryer - Instructions

Open bottom panel and observed back left drum roller wheel wobbling and obviously making the loud rumbling banging sound. Search goggle for Amana model part -- found partsellect.com, and read the list of other DIYs:

Take off the lower and upper front panels (two screws
each);

Remove the front drum glide holder (four screws. Careful
here because of the two wires to be removed for
door open off switch;

Pulling drum forward only enough so the bad roller wheel
would come off shaft after removing shaft snap ring
keeper;

Grease new roller hole and old shaft then place the
new wheel roller on shaft;

Replace all items back after cleaning lent off.

Note: Snap ring was a bit tricky (need snap ring pliers)--make sure it is clipped back all the way on the shaft after new wheel is installed. Also, I thought it was a good idea to put something underneath the dryer drum to support it while it was slightly pulled out -- a block of wood, etc. I found a spot remover plastic bottle that wedged up to support the dryer drum enough to take pressure off the belt during wheel replacement.

I suspected a faulty igniter and disconnected the cable to the igniter and measured the resistance of the igniter and found it to be 70 ohms then I checked the voltage at the same cable towards the power source and found it to be 25 volts ac which should be 120 volts ac. Next I checked the radiant flame sensor and found it to be open (it should be a closed circuit when cold). I removed the flame sensor (with the power off) using a small box wrench and found a broken lead. Replacing the flame sensor solved the problem.

Took everything apart, replaced the igniter flint, and still didn't get heat. Then found out the thermal sensor wasn't running a electrical current through it with voltmeter and just replaced that, now it we have heat again!

first i checked the power supply then i checked each of the switches and limit fuses for continuity.
to do that i had to take the front of the drier off, four screws there. then i removed the bad limit switch 2 screws,the door switch was bad so i replaced it, no screws. since i had the front off the drier i removed the four screws that held the drum in place and replaced the belt. assembled the drier in reverse order when the parts came. 1/2hour total labor.

Replaced both Coils. Purchased M Series coils much less expensive buying coils together instead of seperately. Problem solved.

Removed lower front cover of dryer, located coils, removed old coils by disconnecting the wires and removing the hold down bracket screws. Pulled the old coils out replaced them with the new coils by aligning the index pins on the coils with the holes in the bracket then reattached the bracket and plugged the wires into the new coils. Then closed the cover on the front of the dryer. Dryer now ignites and stays on to heat up and dry clothes.

I inserted the clip

I had an issue where I was not getting any power to my ignitor. After replacing the ignitor with a fresh one, the problem persisted. Next, I went hunting all the fuses and therrmostats for continuity. All seemed fine. So finally I decided to jump the flame sensor which is located on the outside of the flame tube. WHALLA! It ignited the glow plug. So with one 1/4"" nut driver I removed the single bolt from the unit, then I used a pliers to remove the two wires from the old unit. I replaced the sensor with Tue new unit and all was well. It took less than 5 min once I diagnosed the problem.

Removed bottom door panel, four screws. The new part was a slightly different (looks like improved) part, so only had to put two screws back in. Very simple. The only reason it took more than 15 minutes was because I cleaned exposed areas while the panel was off.

Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.

Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website

YouTube's videos to diagnose potential issues. Found the parts at a great price at Parts Select website. Had the parts in 2 days. Installed them dryer works like new.

First I removed the four screws that hold the back cover of the control panel. I then disconnected the two wires from the buzzer and removed two screws holding the buzzer. Install the new buzzer.

Remove the 2 screws at bottom of front panel, remove lower panel. Then remove the two screws at bottom of front door. Lift door forward so spring hooks can disengage from the top panel. remove door, disconnect the 5 wires to the door latch and light. remove the two screws at top of dryer to lift up top panel. Remove 4 screws at the front holding the drum. Disengage the belt from the tension pulley and remove drum. Replaced both roller wheels at the rear of the drum( one was broke). Then remove the screws (about 6 holding the plate in front of the blower wheel. Use a wrench to hold the nut at the back of the motor and a scocket wrench to remove blower wheel. (The Blower wheel was broken from the shaft and was spinning freely). Then do it all backwards to re assemble. i spent more time cleaning the lint from the inside than I took making the repair!

Dryer would only tumble for ~15 min then stop. During this time it would be really loud. Turns out to be a bad Motor. To replace 1) Removed bottom kick panel by removing 2 screws. 2) Then removed upper front cover by 2 additional screws. 3) Disconnected thermostat (marking location of wires on paper). 4) Removed blower housing (3 screws)undid the rib belt from the drum by pushing the pulley wheel up so the belt could be loosened and removed from motor. 5)Removed the front cover of the dryer opening by removing 2 screws. 6) Lifted up and then puled it out to expose the drum. 7) Removed the drum w/belt from the dryer exposing the motor. 8) Removed 2 screws from the motor and disconnected the plug from it. Slid it all the way out. 9) Need to remove (3 screws) the metal faceplate from motor to access the blower wheel (plastic). 10) Unscrewed the plastic wheel and removed 2 screws to remove the motor from the frame. reversed the process for reassembly. Sounds tougher than it really was - only took 30-45 min. Suggestion - write down on paper location of any wires you disconnect - makes reassembly very easy. Also recommend vacuuming any lint in the dryer while it is completely accessible.