MZD2766GES Maytag Refrigerator - Instructions

Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!

These so called factory trained techs, at least the ones that looked at my fridge don't know jack. I explained my problem, they replaced T-Stat refridge side, onother time they replaced door gasket, still not cold enough, found your website,
got all the answers. Ordered and installed,defrost
heater and T stat assy and adaptive defrost control. Remove shelves freezer side, remove evaporator cover 1/4" nutdriver ,defrost with hair
drier, unsnap elec. connector and relaced part.
The ADC, removed screws mounted on roofside
was able to lower plastic panel enough to unplug
the ADC, it just laid there, removed and replaced.
Don't know which part was bad, but I do know that
they are interconnected, at this point I din't care to defrost manually which I did for the last 7 months.
Thanks for your guidance. USMC Ross

This was very easy. I removed all the shelves in the freezer compartment. I removed two nutscrews to remove the back wall. Then I removed the little radiator looking part by removing two more nutscrews. I unplugged the old thermostat assembly and installed the new one exactly like I removed it, then I reversed the procedure to put it all back together. Very easy my wife could have done it. ThANKS!! to Parts Select for the help of all the blogs I read before doing the job.

Chronically faulty electronic board in upper right rear of refrigerator compartment - in Maytag and Jenn-Air. Unplug unit. Remove freezer food to ice chest. Remove baskets and shelves, ice hopper and rear lower panel to expose evaporater fins. Defrost with hair dryer and allow all moisture to dry. Then in refrigerator, remove top shelf food. Carefully remove the upper assembly cover by working the plastic down and slide forward to unhook from rear slide attachments - one on each side. This is the hard part of repair.

Then remove screws from rear wall and just behind the lamps to release the whole control assembly. In the rear right corner is the bad board. Unplug and replace with new board. Reassemble the fridge and freezer. Replug unit.

Confirmed the condenser fan was the problem when I noted it was not running when the compressor was on. Removed 3 mounting screws, unpluggede the fan. Removed and replaced the mounted flange(3 screws) and remounted. Plugged in fan and it started running.

Thanks for the diagrams and quick delivery. This is the second repair on appliances I have made with your parts and probably saved $300-400 in service calls.

took cover off, installed bulb.
lost the owners manual,
part select's schematics were very helpful
thanks

Removed the ice bucket from the freezer. Removed the single screw on the left side with a nut driver, then lift and pull the tray toward you...there is a wiring harness in back of the tray that I had to unplug...easy, pinch the sides of the plastic connector and it disconnects..and the tray came out of the refrigerator...and the cussing started. Since the threaded yoke was stripped it could not be unscrewed from the motor shaft...I took my trusty Dremel Tool and cut the shaft off so the yoke could be separated from the motor shaft and the motor could be removed from the plastic housing. From here on it was a piece of cake...install the new motor and screw the new yoke onto the motor shaft... I think it has a left handed thread, like the old propane bottles used to have..slide the tray back in, reconnect the wiring harness (it only plugs in one way), make sure the tray is sitting on the 4 side supports, put the single screw on the left side and you are done....put the ice bucket back in and flip the bail down and you should be back on business....!!

I Removed the two wires from the old relay. I Then pulled the old relay off the compressor. Next, I had to get the overload seperated from the old burnt relay, which took some care not to break. The old relay and overload is in a plastic compartment. Then I followed the directions that came with the new relay. The only confusion came with getting the two wires back onto the terminals of the new relay, mainly because the old relay was burnt so badly I didn't have any idea how it was originally wired. I crossed the two wires on the terminals of the relay. The compressor would click off and on, but would not start blowing cold air. I swapped the wires on the terminals and it started working immediately.

This was not a difficult project at all.
I removed the ice bin and then unplugged the wiring hareness.
With the old enclosure removed I first removed all of the screws holding the solenoid (look at the way it is mounted before removing all screws). I then removed the drive motor for the ice crusher/dispenser.
The yoke on the drive motor has a left hand thread.
Grip the motor shaft behind the yoke with a thin pair of channel locks or pliers and tap on the yoke in a counterclockwise direction with a small hammer to loosen and remove the yoke.
I then reattached the motor and reinstalled the yoke and then reinstalled the solenoid.
It was a bit of a trick to plug in the wiring harness, but if you use a small mirror you can do it with ease.
Be sure and align the drive motor yoke with the couple on the ice bin at a 90 degrees from the yoke on the motor. Also make sure the dispensing mechanisim on the ice bin moves freely. If not remove all ice from the bin and locate where the ice is jammed and remove it.
Trust me this will save the new enclosure you just installed.

followed the instructions provided and that's it!

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

I don't know anything about repairing a refrigerator - I'm a computer tech. I noticed that the outside of the fridge was warm to the touch and the inside was not getting as cold as it should. I took the lower back panel behind the fridge off and noticed that the fan was not spinning. The local parts dealers did not have the condenser fan motor that was needed but they did say that they do go bad. I decided to order one from PartSelect.com and do it myself. Using a 1/4 inch nut driver and a flat head screw driver to pry the old motor out of the casing, I got the job done in about an hour or so. It's a relativly easy job. Besides the ouside panel screws, there's 3 screws on the inside near the fan blades you have to reach in to get. Pop out the whole assembly, unscrew the nut that holds the blades on and pry out the old motor and replace.. Try it yourself and save a couple hundred bucks!

UNPLUG YOUR FRIDGE BEFORE YOU START> First I removed the shroud covering the lights and controls in the top of the refrigerator side. This was the hardest part, actually. Their are two indentations on the back of the cover and it is really hard to pull that cover off. Anyhow, once you do that, their are two screws, one by each light bulb in the top of the fridge that need to be removed. Their are also three hex head screws that need to be removed, two in the front corners of the assembly, one in the center, back of the fridge. Take those out and the whole assembly drops down. In the back right had corner of the assembly is the adaptive defrost control. Unplug it and set it aside. Plug the new one in. Put everything back together and you are back in business.

Removed about 6 screws. Replaced the solenoid and door kit. Replaced the screws. These parts were easy to replace. They were also super easy to identify and order from the site. I received them two days after I placed my order.
Thanks partselect.com!

1. Turn off fridge and Pull plug from wall.
1a. Turn OFF water supply!
2. Remove rear dust cover to gain access to water valve.
3. Mark power connectors(red/green) attached to water valve before removing them. Remove connectors.
4. Remove supply line from old valve.
5. loosen mounting screw holding old valve in place.
6. remove valve.
7. disconnect two plastic water lines from valve.
8. Cut 1/2 inch off the end of each plastic line to get to un-streached line. Make sure you have enough line to still reach valve!
9. Insert plastic lines FIRMLY into outlets of NEW VALVE to lock in place. outlets are different sizes so you can't reverse them!
10. Install new valve and tighten mounting screw.
11. replace/tighten supply line to new valve.
13. Replace dust cover!
14. Plug in, Turn on fridge.
15. Turn on water supply, bleed air out by drawing a glass of water at door, and check for leaks!
All Done!