This drive hub kit (part number W10528947VP) is for washers.
Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to...
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
These parts are the replacement suspension rod supports for your washer. They are made of plastic and are approximately 1 ½ inches in diameter. This package will come with an 8-piece set of suspension...
This is the replacement cold water inlet valve for your washer. It is mainly blue in color and has two solenoids. The water inlet valve in your washer connects to the water source and solenoid wires, ...
The drain hose carries used water from the washer to your house drain.
$28.81
In Stock
Questions And Answers for MVWX655DW1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
78 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kim
February 11, 2020
What causes water not to come into the machine? The sensor light is on but nothing is happening.Thanks
For model number MVWX655DW1
Hello Kim, thank you for your question. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the wash may fill slowly or not fill at all. The water inlet valve requires sufficient water pressure to function properly. First, check the water pressure to determine that it is adequate. If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.I hope this helps.
14 people found this helpful.
Was this helpful?
Thank you for voting!
Paul
November 30, 2019
Clothes come out wet, does not spin all of the water out of the clothes. Maytag bravos top load washing machine.
For model number MVWX655DW1
Hello Paul and thanks for writing.
Sounds like you need to replace the drive belt Part Number: PS11747978 is in the list of compatible items for your model. We hope this helps. Please contact us anytime.
It is only 2yr old. When I start it the motor is running but the basket is not spinning and all the lights are off. So I unplug it to avoid overheating the motor. What could be the problem?
For model number MVWX655DW1
Hello Felisa, Thank you for the question. This could be a defective Control Board, PartSelect Number PS12114298. Electronic control board manages the washer's functions such as filling, washing, draining and spinning. Hope this helps!
How to remove coins caught in the slot/gap in the basin.
For model number MVWX655DW1
Hello David, Thank you for the question. You may need to remove the Washplate PartSelect Number PS11769534 to get access to remove the Basket and coins. We hope this helps!
Hello, Thank you for your question. You will want to check into the timer itself, that could be faulty and not allowing it to advance. We hope this helps.
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
