MLG19PRAWW Maytag Washer Dryer Combo - Instructions

Removed lower front cover of dryer, located coils, removed old coils by disconnecting the wires and removing the hold down bracket screws. Pulled the old coils out replaced them with the new coils by aligning the index pins on the coils with the holes in the bracket then reattached the bracket and plugged the wires into the new coils. Then closed the cover on the front of the dryer. Dryer now ignites and stays on to heat up and dry clothes.

First I removed the door itself from the unit by taking out 2 screws and lifting the door slightly so that the hinges can slide out of their slots. I then preceded to remove the liner assembly from the door. Once all the screws where removed I separated the liner from the door and continued to remove the additional hardware from the damaged liner and transfered it to the new one. I paid close attention to how items were removed but other than the hinges, all other items can only fit one way. The liner was then replaced and the door put back on the unit. Pay close attention to the door hinges, reattaching them wrong won't allow the door to line up or close properly.

Old latch and door striker were pried out with a flat blade screwdriver. New components popped right in. Repair was less than two minutes.

1. Remove 2 screws that hold door hinges on.
2. Remove 2 screws on opposite side of door hinge and remove 2 plastic clips.
3. There are 2 hex screws that hold the front panel on. Remove these and the panel is held on by a flex clip. Gently twist the top towards the outside of the dryer and they will come free.
4. tilt panel forward and lift of 2 clips at the bottom.
5. Remove the screws under the cover panel which will release the drum holder and lint collector.
6. Lift top of dryer and lift out drum.
TAKE THE TIME SINCE THE UNIT IS OPEN TO VACUUM OUT THE ENTIRE DRYER. CLEAN OUT THE EXAUST TO IMPROVE EFFICIENCY AND SAFETY.
7. I replaced the rear felt by using a flat head screwdriver to lift tabs and install felt. Using the screwdrive I compressed the tabs to hold the felt.
8. The baffle was installed inside the drum and using 2 hex bolts to hold the baffle in. I added 2 washers since the hole was inlarged due to the baffle becoming loose and pulling through the metal drum.
9. Re-install the drum and push rear felt to the outside of the drum.
10. The front drum needs to be installed. Push the felt to the outside of the drum and check the rear felt to ensure it is still on the outsid of the drum. Install 4 hex screws to secure front drum holder.
11. Insatall lint catch unit with 4 additional hex screws.
12. Verify the lint collection panel lins up with the exhaust fan at the base. When units line up tighten all 8 hex screws.
13. Reinstall front cover panel by inserting panel on bottom clips and tilt up to the dryer. The top corners are gently twisted to the outside of the dryer to reattach to the spring clips. Use 2 hex screws to attach panel.
14. Re-attach plastic clips and 2 screws on side opposite of door hinges.
15. Re-attach door hinges with 2 screws. Cleck to ensure the door closes.
16. Check dryer operation.

I had an issue where I was not getting any power to my ignitor. After replacing the ignitor with a fresh one, the problem persisted. Next, I went hunting all the fuses and therrmostats for continuity. All seemed fine. So finally I decided to jump the flame sensor which is located on the outside of the flame tube. WHALLA! It ignited the glow plug. So with one 1/4"" nut driver I removed the single bolt from the unit, then I used a pliers to remove the two wires from the old unit. I replaced the sensor with Tue new unit and all was well. It took less than 5 min once I diagnosed the problem.

Had to move all the concoctions my wife uses on my greasy work clothes [ purple power, dawn dishwash soap,lestoil, etc..] Removed front , removed back panel..Replaced board then motor..Replaced belt while I was in there.I had already changed out the tub bearing assembly earlier..Quite a complex machine when you get in that deep..Runs like new...

My dryer stopped producing heat and everything else was working fine. I did some research on this site and others had the similar problem pointing to the ignitor going bad. I needed to determine which ignitor fit my dryer. What I learned is that some of the parts come with a series number and you need to know which one matches your serial number. My serial number started with 40 and I had a choice of buying the part for a series 10 or 60 series. In my case I needed to buy the 10 series since you either go with the same number as your serial number or lower, never higher. When the part came in I removed the dryer door by removing the 2 screws. I then removed the 2 screws on the opposite side of the door. Once the 4 screws were removed I was able to take the front cover off. The ignitor was on the right side and easy to get to. I unplugged the ignitor and used my socket set to remove the bolt. Once removed I vacuumed the lint in the dryer and installed the new ignitor carefully not touching the black area of the part. I put the front cover back on, put the door in place and put all 4 screws back in place. I started the dryer and it was fixed! This was an easy job to repair that saved me money.

Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.

just replaces the pump , the replacement pump was a little different than OE , mounting bracket different but was able to remove housing and bracket from broke pump and put on new pump , all works fine

Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website

The machine comes quickest appart with a cordless screwgun and a #2 Phillips.

To unhook the wire with spring it is easiest to use a needle nose plier and make a hook from a coat hanger or use a paint can opener.

Pay attention when yo line up the boot with the flange in the back, that the rectagular protrusions line up with the holes in the flange. You may have to stretch the boot a bit and push it all the way in with a dull tool.

Get someone to help you put the wire back on if you want to do it fast and easy. Otherwise hook it on the spring and get the pliers on the loop on the other side and pull it together, torquing the wire back so that it does not make the boot slip fo the flange.

Done

Okay, first of all, just let me say, if I can do this, ANYONE can. I am not very handy when it comes to things like this. I watched online videos and they will walk you through everything. I am so pleased with the results. Quiet as can be now. Before, we would have to shut the door when it was on because the scretching was so loud! The parts on this site were far more affordable than at my local repair store and they all came right to my doorstep. Overall it took me about 45 minutes and three beers :) Good luck!

I removed the screws around the front door. Then removed the front face. I removed the bolts holding the top down at front top corners. I removed the detergent dispensor. Next I removed the spring and hold down cable. I then pulled out the old boot. I then, with the help of my son, pulled the new boot around the drum. Then attached the cable and spring. Next pushed the boot into the front retainer. I then put the dispenser in and the front back on. Good as new. It was not hard as long as you have someone to help with pushing the boot around.

took old one out then i had to strip the connector off new one was to big...

it's best to pull off the back of washer then it is too go through the front thats my only hint