MLE19PRAZW Maytag Washer Dryer Combo - Instructions

If you are cursed with owning a Maytag product then you'll be glad PartSelet.com is in business. I get all my parts here.

My dryer motor burnt a phase. The tear down was very straight forward since there isn't much to a dryer. I did the tear down in the driveway. The dryer was full of lint so I blasted it with compressed air to clean it up. Keep all your parts in labeled baggies as you do the tear down. Reassembly goes much faster. The hardest part about changing the motor was getting the motor clips off. They are tough buggers. I used slip-joint pliers & finally popped them off. This job is simply enough for the average monkey. Just use the diagrams on partselect.com if you forget where something goes.

I shipped everything via fedex 2-day. It took 5 days to get here. partselect shipped it fast. fedex was the problem. I guess the boys at fedex have a public education is they think 5=2.

A year or so ago I replaced one drum wheel. The dryer worked fine for months until it started sqeaking again. When I removed the wheels again the shaft was no longer round but half moon shaped. this allowed the drum to drop lower than it's supposed to. consequently the drum ate through the back drum support. I replaced the back drum support and the roller shafts, in addition to two new rollers. It works great now. The more difficult part of the repair was replacing the rear drum support. It is screwed in from the back and requires two people. Everything else I did by myself. The lesson: If you replace the rollers, be sure the roller shafts are not worn. An asymetric shaft eventually causes more parts to wear out.

Of course I looked at you tube to get the instructions on how best to do the job. It was very helpful. Getting the front bearing out was the major issue. It was so corroded that I could not get it out with a hammer and punch. I had to build a bearing puller which I copied from the you tube video out of a 3" schedule 40 pipe. After that the repair went very smoothly. Putting on the bellows cable and spring assembly took two of us. Also putting the clips that held the inside drum on took two of us. One of us used channel loks to squeeze the two drums together while the other installed the clip. I had trouble identifying the tube seal part number. I phoned for help and the customer service person was very helpful and ordered me the correct part. Thank you

1) Removed machine front by removing four (4) screws. 2) Removed rear access panel. 3) Replaced antiquated motor controller with upgade revision; basically unplug and plug 4) replaced motor and 5) closed up unit. Whole job took about an hour with half the time spent moving the unit to work oo.

I had taken the back off the washer already. The pump was connected to an incoming fitting and the out going fitting with hose clamps. Removed the hose and hose clamps from the old pump, connected the hose and hose clamps to the new pump, reconnected the wiring and that was about it. The pump was mounted to the bottom panel of the washer by simply plastic plugs requiring no tools. It was very easy.

I watched the video

I used a flat screw driver to pop out the old female portion and snapped in the new one. Dryer stays shut. That's it!

Had to remove the tub. Tha bearings had to be removed from the drum. After installing the new bearings(which are available @ O'rReilly's) the seal was't bad

First ya have to find the problem that takes time.
Pulled the front off via the four screws, two on the door and two on the opp side. Removed the two top hold down brackets that hold the top on (on the front), popped out the four screws for the detergent and the top hinged up, The hose was right there. Removed the two hose clamps, found the crack ordered if from you guys.(very fast) slapped it in and put a load in.

got instructions off internet from others who did same repair; after taking inner basket out, used drift to remove outer bearing; seal was difficult to remove but used drift to force innner bearing into seal and seal popped out. had help reinstalling inner basket into outer basket.

We took the washer completely apart. Replaced the bearings, pulley and
belt. We decided to replace anything that involved the spinning cycle while we had it all apart.
It was well worth the time and effort we put into it. It works like a chime
and is very quiet . Silence is golden ! Hopefully it will work another 18 years.

On-line trouble shooting sites indicated that drain pump was likely culprit. Disconnected pump from hoses and removed and replaced pump. Tub to pump hose had considerable scale in it, so replaced that too. Repair was made easier by removing both the front and back panels of the washer to get best access to hose clamps and pump.

Using the pictoral parts diagrams on the PartSelect website, it was a logical process to disassemble the dryer to change the drum drive belt. This was a great opportunity to clean lint from the motor and air passages and inspect all components. Cleaned the belt track, the roller drum wheels and felt seals. Unit now runs like new. BTW - very fast shipping on the replacement belt and it was the right part the first time!

Followed your video; replaced felt seal on front of drum, (torn in two or three places), and replaced both front guide kits,which were ground to the metal, causing the black dust, ( metal shavings). Thanks for the help, Buck. The drum support rollers were OK.

This was fun! Kill the power!
Remove door, remove from panel, remove front drum support, remove drum and belt, remove blower cover, remove blower wheel, remove electrical connector from motor, take two clips off motor mount to remove motor. Put it all back in with new parts. 200 bucks and back in business. Go for it.
Bob