This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This front-load door hinge is a genuine replacement component designed to support the door on compatible washers and dryers, ensuring smooth and secure pivoting during opening and closing. Constructed...
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
If your front-load washer is leaking or making strange noises, this door boot seal might be the fix. It creates a tight seal between the door and the tub to keep water and detergent inside during the ...
Having a problem with a funky-smelling washing machine, or one that just doesnt seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This po...
Upgrading your laundry room? We can help you save space effortlessly with our Whirlpool Long Vent Dryer Stack Kit. Designed specifically for certain Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Ing...
Note: This part has been updated by the manufacturer. It may appear different but will still function the same as the original.
$13.00
In Stock
Questions And Answers for MHW6630HC0
Ask our experts a question about this model and we'll get back to you as soon as possible!
14 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mikail
March 18, 2023
Stuck on sensing fill help me please
For model number MHW6630HC0
Hello Mikail, Thank you for your inquiry. If the washer will not advance from sensing, this is usually an issue with either the water inlet valves, the water level pressure switch or the door lock assembly. When the washer is on the sensing cycling, it will lock the door, and tell the pressure switch to check the water levels and tell the water inlet valves to fill the washer. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. Good luck with your repair.
Hello, my dial on my Maytag front loader fell off and it came apart in three sections. I can't find if I can buy a new dial or how do you put this back together so that I can use my washer
For model number MHW6630HC0
Hi Jennie, thank you for reaching out. The knob does not come separately, you need to buy the whole console assembly, part number PS12711863. We hope this information is useful!
I am looking for hot and cold water screens for the back of my washer. Mine are no good anymore.
For model number MHW6630HC0
Hello Claudette, thank you for reaching out. The internal plastic mesh filter screens are built directly into the hot and cold water inlet valves and are not sold as standalone factory parts. The cold water inlet valve is part number PS17216730, and the hot water inlet valve is part number PS17216729. We hope this helps!
Fabric softener does not dispense every time. Removed and cleaned tray and tray slot already.
For model number MHW6630HC0
Hello Dianna, Thank you for the question. We suggest testing the Water valves. Set your multitester to the ohms resistance scale X 1. Place each of the meter's probes to one terminal. Because the reading can vary from brand to brand and from model to model, there is no one reading you should receive. However, if your test produces a reading of infinity, then the solenoid is bad and the water valve should be replaced. We hope this solves your problem!
Hi Pam, thank you for the question. The drain hose you are looking for is part number PS12584563. This drain hose with elbow bracket is 6 feet long. Glad to be of help!
Using the Torx Screwdriver, we removed the door from the unit. Then we removed all of the screws on the inside of the washer door. After that we flipped it over and opened it up exposing the inside. We couldn't separate them entirely because there was a screw under the latch piece that we couldn't figure out how to get to. However with all the screws out on the inside of the door, we did have enough room to open it up and access the place cover that holds the hinges in. Once we accessed that we removed the roller tips from the old unit and placed them on the new one. Then we reversed the process. With a couple screws in we realized we had put the hinge in reversed from what it needed to be, so we reopened it and switched it around. Then completed replacing all the screws and reattached it to the washer. It opens and closes perfectly and we saved a couple hundred dollars for sure, as the quote to come out had been a $150 trip charge.
Replaced the Whirlpool washer water inlet valve. 1. Unplug washer 2. Close Hot and Cold water valves 3. Remove top cover of the machine by taking out 3 screws in the top back. Slide top back and remove. 4. Water Inlet Valve is located on the back left side, remove tubing using a nutdriver to loosen the hose clamps. 5. Water Inlet Valve is removed by removing the screw in the back of the valve and turning the valve clockwise a little. Replace with the new one, connect hoses, put cover back on, open valves, plug it in. 6. Ran washer and Fabric Softener dispenser now works
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
