MGDB800VB0 Maytag Dryer - Instructions

I spent the most time researching and confirming exactly what part I needed before ordering the shipment. The illustrations and videos available on how to replace the part(s) were VERY helpful and much appreciated.

I followed the instructions seen on video and removed the top and front of dryer. Then pre-fit the new seal - and stretched it out some while dry to make sure it fit the drum. Once fitted, then I glued 1/2 of it and let it stand for at least 30 minutes and then did the 2nd 1/2 after that. I sure needed clips to hold it in place before moving on to complete both halves. Then I tested it and it tested ok.

I have only noticed 1 spot where some adhesive ran out that shows but it was minor. Had to figure out how the main drive belt work with the pressure pully because it had come loose from the drum. Once past that - it just needed reassembly.

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

Removed the dryer door, unscrewed lint vent.

Watched youtube video to problem shoot. Cause determined to be coils bad. Searched web found Parts Select to be easiest site to deal with and had coils for best price. Followed instructions supplied with parts. Dryer works like new.

Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.

My gas dryer would run with heat for 5 minutes in all settings, but kick off and not heat again. Timer would not advance in autodry. Thought it was the cycling thermostat, so replaced that, but did not solve the issue. Ordered the coils, and cleaned out heavily clogged lint from bottom of lint trap, especially right above the fan motor at the bottom of the trap. Received the coils, opened the top and front, took out drum, and replaced the coils. The replacement took less than 2 minutes. Be careful putting the drum back on to make sure the felt is not caught inside the drum. You can give it a spin to make sure. Wear gloves, as I cut myself up pretty good on the edges of the dryer body. The inside of my dryer looks like a crime scene! Anyway, I put it back together, and it runs great. Solved the timer advance issue in autodry, and the heat kicks on and off when it is supposed to. Good luck! Thanks Part Select!

After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

I expected to find a broken blower belt so purchased that belt and the others I planned to replace since the on line instructions indicated that I had to pull the drum to replace the blower belt. I did not, so didn't use most of the parts at all. The instructions that came with the parts, were only slightly helpful because they were for a far different model. Some youtube videos were more help. I had to pop the top, which is easy and explained in the instructions, remove the front panel, which only requires removing two 5/16" small bolts, then lifting it up and off. Simple. With that panel off, I could see the blower belt and it was intact and seemed to work fine. I could have replaced it easily with no further disassembly at that point. However, since it was not blowing the air out of the dryer, I knew there was another problem. So I removed the front of the blower housing, which is four, 1/4" small bolts and it just pulls off. I could then see that the entire front of the blower was packed with lint that had gotten past the normal lint filter. I cleared that all out and checked that the blower itself was intact and clean and there were no other obstructions. When I rotated the blower by turning the motor, it moved easily. So I put it all back together without changing any parts and tested it. It worked perfectly again. I kept the parts for the next time I might need them.

sounded like a pair of shoes was in the tub every time i started it no matter what size the load was. Replaced the back two rollers first and decided to start it to see how it sounded. We were glad. Only the back rollers were bad and the dryer was quietly running again. We would suggest replacing the back rollers first to everyone because the front rollers are more complicated to replace and they may not have to be at all.

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!

I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.

How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.

Removed two hex screws from upper back clips. Removed 2 Phillips screws under lint trap. Used flat head screwdriver to pry up top on front right and left side clips. (FYI: top pry's up off retaining clips in front). Remove two hex screws on right and left front panel. Un-plugged wire harness front right side. Lifted up and removed front panel. This hold the drum in place. Simply removed drum, installed new belt, replaced the two drum wheels and put everything back together the same way I took it apart. 30 Minute project :)

Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen. Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.

Remove old filter
Vacuum out
Install new filter