This manufacturer-approved Refrigerator Pantry End Cap Kit, also known as the Refrigerator Drawer Support, is a kit containing all parts of the Pantry End Cap. It snaps into place on the appliance’s ...
$47.95
In Stock
Order within the next 4 hrs and your part ships today!
This water filter purifies water going to the water dispenser and sometimes the icemaker as well. This part should be replaced if it is causing reduced water flow or just replaced periodically per the...
$69.99
In Stock
Order within the next 4 hrs and your part ships today!
This OEM Center Rail is a white plastic part which supports the crisper frame, which holds the crisper. Fifteen inches long and white in colour, if broken, the support may no longer hold properly. Re...
$34.95
In Stock
Order within the next 4 hrs and your part ships today!
The pantry drawer lid helps keep everything inside the drawer, it acts as a cover and keeps your drawer at the proper temperature by creating a seal. If the door will not open or close, or if the draw...
$204.12
In Stock
Order within the next 4 hrs and your part ships today!
This water filter bypass cap is a genuine OEM component designed for select Whirlpool, Maytag, KitchenAid, and affiliated refrigerator models. Installed in place of the water filter, it allows uninter...
$53.85
In Stock
Order within the next 4 hrs and your part ships today!
This is a genuine replacement light bulb for a refrigerator. The inside of your refrigerator should illuminate when you open the door. If your fridge does not illuminate, you may need to replace this ...
$83.45
In Stock
Order within the next 4 hrs and your part ships today!
This light switch may also be known as a refrigerator door switch or a light switch kit, and is compatible with your refrigerator. The function of the refrigerator door switch is to turn on the light ...
$38.96
In Stock
Order within the next 4 hrs and your part ships today!
This is a replacement pivot block for your refrigerator. It is made of white plastic and is approximately 4 inches long and 1 inch wide. The pivot block catches and holds the door mullion cover when y...
$14.72
In Stock
Order within the next 4 hrs and your part ships today!
Made from durable, transparent plastic, this door shelf bin attaches to the inside of the refrigerator door to store small items like condiments and jars. It’s compatible with select Whirlpool, Maytag...
$87.97
In Stock
Order within the next 4 hrs and your part ships today!
This part allows the cold air from the freezer section to be aired into the fresh food section and it is controlled by the thermostat.
$159.79
In Stock
Order within the next 4 hrs and your part ships today!
Questions And Answers for MFI2570FEZ05
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lynn
March 3, 2023
I am in need of a light for the inside of my refrigerator
For model number MFI2570FEZ05
Hello Lynn, thank you for your question. The Light module is PS12070396. We look forward to hearing from you.
Hi Paul, thank you for reaching out to PartSelect. The freezer heats and cools when it defrosts. This causes the ice to melt a little and then refreeze. If your freezer is just barely too warm or the temperature fluctuates too much, your ice may melt and reform several times before you use it. This can cause clumping, and it can also cause your ice to form irregular shapes. There can be either a leak from the underside of the ice maker leaking into the ice bin or causing the cubes to freeze together. To check this, you will have to remove the ice maker, fill it with water, and look under the ice maker to see if it is leaking. Or the ice is clumping together because you are not using it all quickly enough. If this is not the issue, you will need to replace the water inlet valve, PS11775241. We hope this information helps!
My water dispenser starts off good on demand then slows down a lot as it dispenses water. What can I do?
For model number MFI2570FEZ05
Hello Joel, thank you for reaching out. When your water dispenser starts with strong pressure but quickly drops to a slow trickle, the issue is most likely with the water filter. A clogged, aged, or faulty water filter restricts water flow through the system, causing pressure to build behind the blockage when the dispenser is not in use. When the paddle is pressed, the stored pressure creates a brief, strong burst of water, followed by a slow stream as the restriction limits continuous flow. Replace the filter, part number PS11722130, to fix the issue. We hope this helps!
Ice maker stopped working. Replaced both water valve and ice maker but no change. Water line is clear and water flow at the door is normal. Filled tray manually and the ice dispensed properly.
I'm running out of ideas, thank you for any advice.
For model number MFI2570FEZ05
Hi David, thank you for getting in touch. Since you have already replaced both the ice maker and water valve, confirmed the water line is clear, and the ice dispenses properly when the tray is filled manually, the main control board is the next likely cause. The control board sends the power and control signal needed to initiate the ice maker’s harvest and water-fill cycle. If the board is not sending the proper signal even though the replacement ice maker and valve are working, replacing the main control board, part number PS12070401, can help restore normal ice production. We hope this helps!
Pressed in the end of the filter cover, lowered it down part way. Twisted the old filter 1/4 turn and removed it. Set in the sink to drain. Inserted new filter and twisted it to lock. closed cover. Done. Total time @ 1 Minute.
Removed the fruit & veggie drawers & the deli (pantry) drawer. Took out the 3 screws, removed the attached parts, put them on the replacement part, reattached it and put the drawers back in.
Here's the part I want to share: PartSelect had a expanded diagram showing the correct part and sufficiently detailed to figure out the repair before the part arrived. That's why I ordered from them. Secondly, I ordered the part Thursday morning--and the thing was sitting on my porch when I came back in from my evening out Saturday--2 days later!!!
Remove food off of lower shelf, remove the two produce drawers, remove large lower drawer, remove glass shelf, remove three screws holding end cap in place. Once end cap was removed the drawer track could be removed and placed on new end cap. Installation of new end cap took less than 5 minutes. Most of the time spent was removing/replacing food and cleaning the shelf/bins. PartSelect was awesome BTW!
