MFI2269VEW4 Maytag Refrigerator - Instructions

I removed the ice maker assembly from the freezer compartment (four nuts/ nut driver) and unplugged the wire harness. I discovered the nature of the problem and I went on the Internet to look for replacement parts expecting I'd have to buy the entire ice maker. When I found PartSelect.com I looked through the pictures of the parts available for my ice maker. I found the correct part quickly and easily. And having an acurate photo on the site, I was able to match all the key features of the mold I had with the one on the screen. I ordered the part, and installed it the day it arrived with just a Phillips screwdriver and a nut driver. It functions perfectly.

I removed the glass top and then rail and frame.
I had to remove the gaskets from the old frame and put them on the new one.
The steel support and the slide mechanisms were difficult to remove. I needed a screwdriver to do this.
Some directions would have helped here.
It was easier to snap them back into the new frame.
I set the frame and then rail back into the refrigerator,
replaced the glass.

Turned old one until it snapped out. Replaced it with a turn.

Removed the drawers and shelf unit above the shelves. Installed the new rail and put the shelf unit and drawers back in. Less than 5 minute repair. Very fast delivery of part and reasonable pricing.

First I removed the icemaker from the freezer by removing two horizontal screws holding it to the side wall, and one vertical screw holding the front to a bracket coming off the side wall. Then I used a flat screwdriver to unlock the electrical plug. (After doing this, I realized that this wasn't necessary at all, and this part could have been changed just as easily without removing the icemaker.) On the front, there is a white cover with Ice Maker Plus. Use a flat screwdriver to unlock the tangs and remove the cover. There are three screws in the corners that once removed, will allow the motor assy. to be gently pulled straight out. On the back of the part, you will see many gold lands that the timer touches. I don't think there was anything wrong with my motor. I had two spots where the gold plating was worn off, so I suspect it was not making contact, and the whole process would stop. Slide the new part in place making sure the teeth on the gears line up (not a big deal), and secure with the screws. Install cover and you're done. Mine has been making ice like it was brand new.

Removed the metal cover over the HV electronic board on the back of the unit. Using a flat head screwdriver I unsnapped the plastic cover and removed it. I unplugged the 5 or 6 cables from the electronic board. Bent back the plastic tabs holding the board. You might think they are going to break but they bend. I lifted the board out and replaced it with the new one. Then plugged the cables in being careful to align them first. I then applied power and the refrigerator came to life. I followed the programming instructions that came with the refrigerator. You can get those online also. The unit began to run and in a few minutes the compressor came on. The unit began cooling and life was good again!

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Watched Partselect video of P-trap installation.Removed water line & back cover& disconnected wires to water solenoid .Removed old drain tube & old problematic rubber funnel. Used contact cleaner to clean rubber residue from drain line and used a little silicone to aide reassembly. Job went well thanks to video.

Took drawers out, inserted the rail and put the drawers back in and voila. Fixed.

changed the starter connected to the compressor

took the pantry drawer out removed track replaced and put on new door... very simple

Turned the old one to unseat and replaced with a new one in the reverse order.

Simply move the appliance for access to the back side. Removed the lower metal access panel, locate the compressor ( black round object ) parts are on the left bottom of the compressor. Simply unplug the parts, and replace with new parts.The hard part was, getting my 72 year old body in position to do the job. As far as getting the right part, a young lady in Nova Scoita is the one to ask for help !! Ordered parts one day, and they were in my hands the next morning!!

Repair was easy and producing ice within five hours.

The repair seemed simple, I just needed to remove the old bracket -- 4 screws -- and slip the new one on.

The tricky bit is that the roller bracket holds the weight of the fridge. So in order to make sure that the fridge did not fall over, and to keep the installation point off the ground so that I could align the screw holes, I needed to shim up the side of the fridge that I was working on.

To tap in the shims, I used a hammer and a spare chunk of wood. I ultimately used 3 shims, and kept tapping until the roller wheel could roll freely. Then I knew that the fridge was high enough. After that, it was pretty easy to remove the 4 screws, align the new bracket, and replace the screws. After that, in order to get the shims out I could just extend the foot brake as it was designed, and that lifted the fridge enough for me to easily slide out the shims. After that I just had to level out the fridge by adjusting the two feet.