MEW6627DDB19 Maytag Wall Oven - Instructions

Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Took the door apart and replaced the hinge, very easy

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Parts package contained no instructions. Found all instructions on internet. I used Phillips head to remove two screws on anchor plate of Long Oven Sensor. Located at upper left, back corner of oven; access to screws is not simple/easy. Screws back out w/o difficulty. Pull/extract sensor harness through hole[back of oven] which required pushing aside insulation. The harness barely fits thru hole in oven back metal wall; I recommend using needle nose pliers ( which I ended up doing ) for ease of extraction. Disconnect harness plastic interlok clips. Perfect reconnection of new clip harness with ease. Reverse procedure to complete installation/repair. Done in just over 35 minutes due to wrestling with harness extraction through minimal hole opening. Failure occurred on Thanksgiving Day with 22lbs turkey in oven. Top of turkey contacted sensor tip which eventually caused sensor fault; result was scorched upper breast and oven shut down [safety by design]. Cook top was still operative; clock and all readings on digital control panel ceased. With new 'long oven sensor' installed - good as new. Will be sure to buy turkey(s) under 20lbs in future. Jim in Seattle

Removed the back of the stove, un-pluged the sensor wires, removed the sensor from inside the oven. installed the new sensor, pluged in the wires, and replaced the back of the stove. A phillips screwdriver was the only tool needed.

The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires togather. The oven cooks fine, I have not tried the cleaning cycle yet.

We took the back off the stove and unscrewed the two screws from the inside holding the sensor on and pulled it through and plugged it in and then replaced the screws. Very easy. We are still having trouble as the display does not read the same as the tempature is in the oven.

bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!

Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call

The "PartsSelect" General discription of the parts funtion helped me to confirm my suspitions that there was some form of temperature registering problem. I whatched the short video they provided on how to change the part out, even though, in this case, it's pretty self explanitory.The part was in my hands a day erlier than promised and in reality, much earlier than I had anticipated from the beginng. It took me all total, 20 minutes to exchange the part out and have the oven in operation again.

Watched the video and things went exactly as planned. Love this website will use them again when I need a repair.

The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.

The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.

Slid off door and metal front. Then just screwed on new handle as instructed. Simple.