MER8770WB0 Maytag Range - Instructions

Can of Corn fix! Remove the two screws in the element cover plate (they're in the back- left/right corners). Remove the two screws that hold the element in place. Pull out the two prong ends of the plug in portion and hold the black / white leads so they do not fall back in behind the unit. Plug in new element (it only goes one way). Screw everything in and test. Place cover plate on after test. Like I said ... a "Can of Corn" fix!

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

I turned the braker off the electric range and removed the bottom plate that housed the bake element (two screws had to be removed). There were three screws that held the bake element in place. I pulled the bake element from the two electrical prongs that connected to the oven. I replaced the element and put everything back in place.

More importantly than all of the above. I received the part from Partselect in two days. When I originally put the eleemnt in its place it did not work. I called partselect and was issued another element in two days. The people I spoke to on the phone were proffessional and sympathetic to my problem. I will definetly recommend this company to other people. Thank you very much....

remove stove , unplug power , took back panel off, disconnected wiring to the heating element, from the inside of the stove removed bottom plate /two screws/, removed heating element /two screws/. installed new element .put other parts in order they were removed

The Maytag stove has a hidden element and therefore I had to remove the bottom cover to expose the element. I had to remove the three screws that held the element in place. The element was badly bent out of shape and must have been that way since new. It was difficult to remove the element and I had to pull the stove out to access the electrical connection in the back to disconnect it. The replacement part was a perfect fit and the installation of the new part went with out hitch and the oven works perfectly.

removed door (no tools required - just lift and pull door out of range). removed front door panel with a screwdriver. removed/replaced door hinge with nutdriver. replaced front door panel with screwdriver. replaced door on range (again, no tools required). then installed tip-over bracket to floor/wall behind range. measured location, drilled pilot holes and installed wood screws into the floor and rear wall stud.

replaced light socket but did not repair problem. must have burned the motherboard.


pleased with service from your company.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Screwed in light bulb and glass protector

very easy

i simply followed your instructions,so easy my wife could have done it with her pink screwdriver!!! thanks for your help.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you