This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$22.58
In Stock
Order within the next 1 hr and 43 mins and your part ships today!
This bake element has push-on terminal ends.
NOTE: This element has been updated by the manufacturer. New installation screws are required. Screws are sold separately.
$50.69
In Stock
Order within the next 1 hr and 43 mins and your part ships today!
The oven sensor detects the temperature within the oven cavity and sends the information to the control board. If your oven is not heating evenly, has little or no heat when baking, or is too hot, you...
$53.22
In Stock
Order within the next 1 hr and 43 mins and your part ships today!
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$28.95
In Stock
Order within the next 1 hr and 43 mins and your part ships today!
Use this scraper for your ceramic/glass cooktop. It has a retractable blade and is an all-purpose tool for cooktops, mirrors, windows and tile. Use it to also remove paint, paper, dirt, stickers and more.
$13.68
In Stock
Order within the next 1 hr and 43 mins and your part ships today!
Sold individually. Lock washers are used with screws when vibration from an appliance may cause the screw to loosen. Lock washers are also used in the electrical components of an appliance to ensure ...
$10.95
In Stock
Order within the next 1 hr and 43 mins and your part ships today!
This wheel and shaft is used to open and close the bottom storage drawer of a range/stove.
No Longer Available
Questions And Answers for MER5730AAW
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Arlene
November 28, 2019
Specificaitons for serial number 15810804wz Maytag stove
For model number MER5730AAW
Hello Arlene, thank you for your question. You can see the owners manual at the following link.
https://partselectcom.azureedge.net/assets/manuals/E10F3DA7CFDA530262CF17CBD4282BC78D78D585.pdf
I hope this helps!
Was this helpful?
Thank you for voting!
Tabatha
May 11, 2023
The light on the stove panel stays on after the burners are turned off. Is it the burner switch ?
For model number MER5730AAW
Hi Tabatha, thank you for reaching out. Based on our understanding of the issue, we would suggest you check the infinite burner switch-8 inch, part number PS11744487, and the infinite switch-6 inch, part number PS11744486. If any one of these switches is faulty, you may need to replace it. We hope this helps!
First, I unplugged the oven. Then, I removed the two screws that hold the element in place. After that, I gently pulled the element toward the front of the oven until the wires were exposed. I disconnected the wires from the old element, removed the old element and then attached the wires to the new baking element. I gently pushed the new element back into the screw holes and screwed the new element in place. When I plugged the oven back into the wall I heard a pop and thought I'd blown up the oven! Turns out the breaker popped...after fixing the breaker, I turned the oven on and the element worked just fine. I highly recommend PartSelect.com for their fast shipping and great products. I will be ordering from them again for future appliance parts.
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Moved the Appliance out unplugged it and removed the backing plate then Remove the Knob and unscrew the infinite switch then marking the 5 wires to know where the go on the new switch, removing and replaced it with the new one
