MEDB800VU0 Maytag Dryer - Instructions

Removed the broken catch with a pair of needle nose pliars and replaced it the same way. Took about 10 minutes. Saved a Service Call

Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.

We watched the video at whirlpool.com! Made it so simple anyone could have done it!

I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.

Just watch YouTube videos. They show you how step by step. Easy to install. Clean all the dust out while dryer is apart if you can with a vacuum.

BEFORE ANYTHING ELSE UNPLUG THE POWER AND TURN OFF THE GAS SUPPLY 1. unscrew the 3 nut screws at the back to remove the cover lid. 2. pull the control console cable from the electronic board. (only 3 wires on it).3. unscrew the 2 nut screws of the control console then remove it by pulling up.4. unscrew the 5 screws to remove the door. (pull little up to unhinged then remove). 6. unscrew the 5 nut screws to remove the lower siding. 7. unscrew the copper 4 nut screws then remove the lint suction fixture 8. unscrew the 4 nut screws to remove door fixture ,then just lay next to the machine.(the wires are long enough so you don't need to unplug and separate it from the machine.9. remove the belt by pulling the idler pulley towards the motor pulley (against the tension spring) 10. remove the drum by lifting a little bit upward. 11. remove the plastic triangular lock using a small screw driver then remove the idler pulley wheel then install the replacement. (clean your machine using a vacuum cleaner and remove all the lints). 12. install back the drum, be sure to set the drum belt to the right position. (groove on drum side). 13. install back the belt to the pulley the same procedure as to remove it. 14. assemble back what you have removed. end.

Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.

By watching the video it made the job much easier than I thought it would be. I was very pleased with the speedy delivery of the Dryer kit I had ordered. I had called a local repair facility and they wanted twice as much for the same parts.

Getting the cabinet open is always fun. Prying the top open without breaking the clips. I took a small pry bar, covered the end with gray tape and found the the clips located on the front outer edges. You push in on the metal clips from the front and lift the top off the plastic alignment dowels. Remove the back, and two front panels. Removed the drum and vacuumed out everything (inspect). Remove old seal, idler pulley assembly from back of dryer (spring & bolt & note belt routing). Glue new felt seal on drum, slide on drive belt, bolt on new idler assembly & attach spring. Attach lower inner front panel screws. Flex out front panel and lower in the drum (make sure the felt seal lip is not folded over). Complete installing front panels. Slide belt towards center of drum (see old mark). Flex idler assembly and route drive belt. Hand spin drum to align belt. Plug in and run dryer briefly to confirm things run smoothly. Align lid clips and close. Unplug and attach back panel and vent hose. ALL DONE.

i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.

Open breaker and ensure power was off. Checked heating components for continuity.Found thermal fuse had an open circuit.Replaced High limit thermostat and thermal fuse.Now is a good time time check for free flowing vent piping.I discovered mine was crimped below the floor and caused lint build up and obstructing the flow which could have led to the thermal fuse blowing.I replaced the vent piping as well.My wife says the dryer works better now than it ever has.

very easily

Followed video step by step. Perfect instructions. I’d only add that you should get and wear mechanics gloves. My hands got torn up by the sharp metal edges taking apart and putting it back together. Ouch!!
So happy with Partselect though. Super fast shipping and a perfect instructional video. Thanks!!

P.S. Wear gloves!!!

Take door off dryer (unscrew four screws). Lay door on flat surface. Using glue provided glue down new seal. Put dryer door back on and you're done!

I don't have instructions ,I watched the link provided by parts select. I just wanted to say I have never been a wiz at home repairs.it took so long because I am 62 with autheritis in my hands and the dryer had to be taken down to a motor and a base but I took the time to clean every inch of the dryer scary to see so much dryer lint inside the dryer.i am just going to say if I can do it anybody could fix their own dryer ,just take your time ,let your hands take a break. And keep the repair instructions close by