This dryer repair kit consists of five commonly replaced dryer parts: one multi-rib belt (part #661570V and measures 93 1/2 inches long), four drum support rollers, one idler assembly, nine tri-rings,...
This Idler Pulley includes the tri-ring and gasket and everything included here is manufacturer-certified. This part maintains correct tension on the drive belt in order to spin the drum properly. If ...
When connected to electricity the dryer heating element glows red hot and generates heat. When air is blown over it, it heats the air which is used to dry the clothes. The heating element fits inside ...
This dryer lint filter is designed to capture lint and debris during the drying cycle, helping maintain airflow and prevent potential fire hazards. Measuring approximately 12.5 inches wide by 10.5 inc...
The Drive Belt is a 93 1/2" belt which wraps around the dryer drum to allow tension and movement. If broken the dryer will not turn properly, or there may be loud noises. The part is rated as "medium"...
This thermostat may differ in appearance, but functions the same as the original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.
This is the moisture sensor for your dryer. It helps detect the amount of moisture in your clothes during the dryer cycle. If you notice your clothes are still wet after an automatic dryer cycle is do...
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
Also known as Thermal Cut-Off kit. The thermostat acts as a safety mechanism that keeps the dryer from overheating and the fuse is like a backup system - it's set to trip at a higher temperature than...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This part seals the drum to prevents air from escaping. This includes silicone rubber adhesive.
$56.40
In Stock
Questions And Answers for MED6230HW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
8 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Nan
October 22, 2024
How much is a control board for this model?
For model number MED6230HW0
Hello Nan, Thank you for your inquiry. We show the compatible control board as part# PS16543591. The current price of the part is listed on our website, plus shipping and taxes. We hope this helps.
How do you get the top off of this dryer? I have a coin stuck in one of the baffles and need to get the baffle off to get it out.
For model number MED6230HW0
Hi Kevin, thank you for contacting us. To remove the top panel, we would suggest following these general instructions. They may not be for the exact model but will help you with the disassembly: First, remove the console by removing the screws on the rear panel. Detach the console clip and lift the console. Remove the wirings to separate the console from the top. Then, remove the screws from under the console area on the top panel. Slide the top panel and lift it. The top of the drum will become visible. We hope this information helps!
Was this helpful?
Thank you for voting!
Jeff
May 4, 2024
One of the plates in the terminal block came out for the white wire. It is the plate the screw threads into.
For model number MED6230HW0
Hello Jeff, thank you for reaching out. The plate you are looking for does not come separately, and it comes as a part of the terminal kit, part number PS334181. Customer service is available 7 days a week if you need help placing an order!
Power is coming into dryer but the touch panel will not respond
Drum light does not turn on when door opened
Service guy came and started it and left
One load later will not start
Before failure it displayed power failure message
Service guy said the diagnostic function showed no other messages
For model number MED6230HW0
Hello Richard, thank you for getting in touch. Based on the description that you have provided, we would recommend checking the wiring of the user interface board and the electronic control board. If the issue persists, you may need to replace the electronic control board, part number PS16543591, to fix the issue. Glad to be of help!
Hello Charles, thank you for contacting us. Based on the description that you have provided, we would recommend checking the door hinge, part number PS16620360, to fix the issue. We hope this solves your problem!
Remove the kick plate from the bottom of the dryer by sliding a putty knife along the top edge to release the plastic clamps, one on each side about 4" in from the edges. The kick plate folds out and down. You will see the heat shield on the right, held in by one hex head screw. Remove screw and heat shield. The element is positioned in an open-front housing and is fastened to the left side of the housing by two hex head screws, located on the "rail" of the element and right near the two wires. Remove the hex-head screws that hold the element in place and disconnected the two wires by pulling them out by hand or with needle nose pliers. The only difficulty here is the cramped working area...I recommend a stubby socket driver for these two screws. Most of this I had to do by feel because I could not see the screw heads. Once the screws are out and the wires have been disconnected, slide the old element straight out toward you. You may need to disconnect a small plastic hose located to the left front of the element, but this hose just pulls right off. Vacume the dust & lint build-up out of the whole area, wipe out the element housing and clean up the whole underside of the dryer prior to installing the new element. Installation is reverse of removal. It also might be a good opportunity to clean out your exhaust duct and the vent to the outside. (Never use the aluminum foil-accordian-type duct.) If the exterior dryer vent has any kind of screen over it, remove it and get rid of it. Screens collect lint, lint builds up and burns out elements.
The issue was the idler pulley. First I began opening up the front panel based on a youtube video but soon realized the model was slightly different and required a lot more items to remove. I saw the pulley in the back with nothing in the way so I put the front panel crap back on and removed the rear panel. There it was, very simple to remove and replace. I'm not looking forward to drum rollers though. Hopefully they're aren't as difficult as they appear.
