Models > MDG25PDAGW2 > Instructions

MDG25PDAGW2 Maytag Dryer - Instructions

All Instructions for the MDG25PDAGW2
121 - 135 of 287
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lint screen tore and had a side that was loose so it didn't catch all the lint and cut your fingers
Removed the old screen and simply put in the new one
Parts Used:
Lint Filter
  • Wayne from ALBANY, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wrong parts were shipped, phone calls got continuous recordings to send email. Sent email sent on 4/2/2020 and now 4/14/2020 no response and no return of $20.52.020
Had to call service company to come and do the repair and they had the correct parts. PARTSELECT is a very terrible company to do business with. They sent incorrect parts and will not answer the phone or respond to emails after two weeks. will report to BBB.
Parts Used:
Screw
  • Rich from GOODYEAR, AZ
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
would not heat
I started by changing the part that had the highest percentage to solve this problem , the top three didn't work , the fourth part, the disposable thermostat, and the last one that could be done from the front worked.
Parts Used:
Dryer Radiant Flame Sensor
  • Arthur from VALLEJO, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F-26 Fault message
Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger
Parts Used:
Dryer Thermostat Internal bias
  • DW from ALVIN, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Parts Used:
Roller Support Tri-Ring
  • Joe from St. Louis, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer door wouldn't catch and stay shut
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Parts Used:
Door Catch Kit
  • Melody from TEXARKANA, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door would stay closed
just replaced parys
Parts Used:
Door Catch Kit
  • william from KILLEEN, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Torn filter seal
Remove old filter, throw it away, replace with new filter.
Parts Used:
Lint Filter
  • James from SCOTTSDALE, AZ
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken dryer door catch
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
Parts Used:
Door Catch Kit
  • Kenneth from UPPR MARLBORO, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken door catch
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Parts Used:
Door Catch Kit
  • Frank from ENDICOTT, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken door catch
I followed your short video and found it very easy to do
Parts Used:
Door Catch Kit
  • Susan from HUDSON, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would not heat.
The hardest part was figuring out how to access the dryer mechanism. This Amana dryer has a lower front panel that is removed and not the top. There are few instructions available for this configuration. Then the part locations do not resemble the video instructions for trouble shooting. I discovered the broken part because when fiddling with the wire connections the metal tab disconnected due to fatigue or corrosion. Removing, identifying and replacing the flame sensor was quite simple. The dryer now works as before. The dryer is 23 years old. The most time in this repair was spent figuring out how to disassemble and identify a different configuration than in the videos.
Parts Used:
Dryer Radiant Flame Sensor
  • Jon from WILLIAMSBURG, MA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer door wouldn't catch, catch was broken
took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......
Parts Used:
Door Catch Kit
  • Theodore from Tyler, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door catch broke therefore dryer door would not close
just put the new part in the door---sooo easy! THANK YOU!
Parts Used:
Door Catch Kit
  • vernette from sprague, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer Door Wouldn't Shut
My husband is the one who fixed the door. He said he just popped it into place and was done in just a couple of seconds! The best part though was the quick service we received. . . I ordered the part around 10:30 in the morning, and it was at my front door by 5pm the next day!!! What great service!!!! We will definitely do business again with partselect. Com if we ever need more parts.
Parts Used:
Door Catch Kit
  • Megan from Kettering, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the MDG25PDAGW2
121 - 135 of 287