MDE20CSAGW0 Maytag Dryer - Instructions

Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.

I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.

Just watch YouTube videos. They show you how step by step. Easy to install. Clean all the dust out while dryer is apart if you can with a vacuum.

BEFORE ANYTHING ELSE UNPLUG THE POWER AND TURN OFF THE GAS SUPPLY 1. unscrew the 3 nut screws at the back to remove the cover lid. 2. pull the control console cable from the electronic board. (only 3 wires on it).3. unscrew the 2 nut screws of the control console then remove it by pulling up.4. unscrew the 5 screws to remove the door. (pull little up to unhinged then remove). 6. unscrew the 5 nut screws to remove the lower siding. 7. unscrew the copper 4 nut screws then remove the lint suction fixture 8. unscrew the 4 nut screws to remove door fixture ,then just lay next to the machine.(the wires are long enough so you don't need to unplug and separate it from the machine.9. remove the belt by pulling the idler pulley towards the motor pulley (against the tension spring) 10. remove the drum by lifting a little bit upward. 11. remove the plastic triangular lock using a small screw driver then remove the idler pulley wheel then install the replacement. (clean your machine using a vacuum cleaner and remove all the lints). 12. install back the drum, be sure to set the drum belt to the right position. (groove on drum side). 13. install back the belt to the pulley the same procedure as to remove it. 14. assemble back what you have removed. end.

Repair job took less than 10 minutes: 1) Unplug Dryer 2) Remove Lint screen and 2 Phillip screws 3) use flat putty knife to depress lid latches while lifting (latches located approx 2 - 3 inches from each side. 4) unplug defective door switch 5) remove 2 Phillip screws that secure the door switch. Reinstall switch repeating the above steps in reverse order and your done.

First, let me start off by saying - this part wouldn't normally break. Because it's a stackable, and my dryer motor went out, the repair company had to move the entire unit from the cubicle. When the repairman tried moving it by using the washer lid ... lets just say he broke the clip. And then we could never get them to come fix the part they broke!

So, I finally ordered the part myself after studying schematics online. I am not a repair person. So, if I could figure this out - anyone can.

Take the middle cover between the washer and dryer off. There are 3 screws holding that panel on. Set the panel and screws aside. There are two "S" shaped clamps at the back. Lift (hard) the front of each one. They will snap free - freeing the whole top of the washing machine. The top has the lid connected. Pull the top towards the front and then rotate it counter-clockwise. It will come right off. This will free up the area the clips go on.

Take the lid completely off to get it out of the way. The clips fit in the holes on the front left and front right. The large square side goes up, and the small side snaps into the hole on the base. Make sure the groove is facing forward for the top cover to slide into. To get the clip to snap into the hole, put the front side down, and push (really hard) on the back side - the side towards the back of the washer. It should snap into place with some pressure.

Now, just put the top cover (with the lid attached) back on, rotate it clockwise, re-clamp it down and replace the middle panel and 3 screws.

Easy, right?

By watching the video it made the job much easier than I thought it would be. I was very pleased with the speedy delivery of the Dryer kit I had ordered. I had called a local repair facility and they wanted twice as much for the same parts.

removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!

i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.

Old door catch came out, new one slipped in. All works great.

The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.

I followed directions found on several similar YouTube videos since the instructions included in the Whirlpool parts kit were not for my model dryer. I found that the original idler pulley was not rotating and the belt had worn a groove through it. I replaced all 4 roller wheels, idler pulley and the belt. Problem solved.

I identified the correct catch of the three that were included in the package by matching its number to that on the old catch that I had pried out of the door using a flat screwdriver. I centered the new catch over the square hole in the door and pressed it into place. Then I used some needle-nose pliers to twist and remove the metal pin that fits into the catch from the main dryer housing. I replaced that with the new piece included in the kit, gently tapping it into place with a hammer. The repair complete, the door worked perfectly. Thanks for your help and for the speedy delivery of the kit.

had to take front off of Dryer then was able to replace drum roller

It is odd that this part needed replacement but I am in an area near the Atlantic ocean in a vacation house which is vacant most of the year. The exhaust vent probably brings excessive moisture down to the dryer in the basement. The screen you can see at the inside back of the tumbler (where the heated air enters) rotten out, pieces fell inside and there was danger of something falling in and catching fire. I found no useful source for information (including YouTube) as this part is most easily replaced from the rear of the dryer and the available info was about repairing the heating element, the circuit board, or the exhaust venting pieces which is done from the front.

The bottom line is that the back removes easily. You should:
1. unplug and remove the exhaust shoot
2. remove the top per YouTube or other source
3. take off the back panel over the electrical connections and unscrew the ground; tuck it inside. Don't undo any electrical connections except the ground
4. take off the screws holding the back on (8-9, one is hidden above the exhaust vent) and pull it out of the way; you then have compete access to the "DUCT-AIR" part
4. undo the clip that holds the vent tube (from the heating element) to the part
5. remove the screws that hold the part to the inside back (3?) and push it out of the way
6. remove the clips and remove the old part
7. reassemble in reverse order

I'm over 70 so I took lots of time and breaks but was still done in under two hours. The 2 clips holding the heater element tube to the part were badly rusted and should have been replaced but I made do with the old ones.