MDB9206AWW Maytag Dryer - Instructions

Thanks to reports from others, I concluded that most likely the gas ignition coils (one or both) were no longer functioning properly. I replaced both with the 'M' Series New Style Coil Kit which is about 1/2 the price of either coil individually -- yes,true,go figure! The actual replacement took only about 10 minutes. What was most difficult and took the most time was the removal of the front panel of the cabinet -- this was difficult only because there were no instructions in my owner's manual (or any other source I could find) and it took me awhile to figure it out. Now I could do the whole job in about 20 minutes! The detailed instructions from others as to the process of replacing the coils was invaluable -- I don't know if I would have been able to figure that out on my own. But most important was the information that enabled me to diagnose the problem in the first place. Thank you, all you previous comment contributors.

Take old out, slide new one in. Perfect fit.

Found the high temp thermostat was shutting off the gas after just a few seconds. Tested the thermostat and it looked like it was opening at 180 degrees as opposed to the rated 240 degrees, so I ordered one from PartSelect, which shipped the next business day. Replaced the thermostat and no luck, still shutting down after a few seconds. Turns out the duct going outside the house was blocked with years of lint stopping the air flow. Cleaned out the duct and the dryer is working fine again. Wife is happy she won't have to go to the laundromat.

Unplug dryer. Removed the screws on the right hand hinge, lift and remove the door, remove the screws in the left-hand side, slide top of front cover out and lift off of metal tabs and set aside. Used a small Shop-Vac to clear any dust or lint from the appliance housing. Un-clipped quick disconnect connectors from the igniter, flame sensor and coils. Loosened but did not remove screw holding igniter slid igniter coil off following slot in igniter coil. Unscrewed top bracket screw to flame sensor, slid other end out of tab in slot, bracket must be slightly bent to remove old and insert new. Unscrewed top brackets to coil. Warning assembly screws were installed extremely tight had to break them free using small vice grips so phillips heads would not strip, enough clearance to gain purchase on the sides of the screws head with small vice grips. Place new coils into slots and screwed brace back into place. slid new igniter coil onto the existing screw, inserted metal tab into assembly for heat sensor, new part came with replacement bracket. tightened all screws. reconnected quick connectors to all 3 parts. reversed process of cover disassembly to reassemble and reinstall door. plugged dryer back in. fix successful consistent heat restored.

unplug dryer; remove dryer door; remove front cover; thermal fuse located on heater underneath and beside drum; remove two electrical leads on fuse; remove two screws holding fuse in place; install new fuse and do the above in reverse; clean lint from duct; plug dryer into

Accessed the front of the dryer cab by removing 4 screws (2 cover, 2 hinge) which also allowed the door to be removed. The front panel pivots at the bottom, towards the front. Changed the igniter first (loosen 1 screw, slide old unit out, slide new unit in, retighten screw, transfer electrical connector) though the unit looked OK, then changed the gas valve solenoid coil packs (disconnect electrical plugs, remove coil bracket (2 screws), swap new coils for old, and reassemble). Vacuumed up loose dirt and reinstalled front panel and door. Also removed, cleaned, shortened, and reinstalled the dryer flex duct as a maintenance item. Dryer works perfectly again!

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

took out the old lint filter and put in the new one.

It fit perfectly! the part arrived quickly.

I was very satified with my experience!

I removed the dryer door and attaching hardware to other covers. Raise the top cover and prop it up. Remove the drum retaining cover and disconnect the door switch wires, making note of their locations. Release tension on idler and take belt off of motor. Pull the drum out with belt still around it. Vacuum lint and dust from inside cabinet. Use snapring pliers and remove the snaprings on the drum rollers. Remove the old rollers and washers, clean the shafts and apply a light film of oil on the shafts. Install new rollers and plastic washers on shafts and secure with snaprings. Remove the "E" clip from the idler shaft and remove the old roller. Clean and lube the shaft and install the new idler and clip. Place the new belt on the drum with the ribs against the drum. Put the drum in place and install the front drum retainer. Position the belt around the motor pully and tensioner. Rotate the drum to get the belt to track. Attach the remaining covers.

We could not find directions for the brand that we have. First we took the back off, which we did not need to do.
lift the top of the dryer, remove the front remove drum. Place belt on front of motor, wrap double belt around support on bottom of dryer, open the remaining belt and stretch around drum. Hold drum in place, replace front and top.
Need at least 2 people, not at all intuitive.

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

I took out the old worn out part and replaced with the one I order.

AS it turned out the problem was not the igniter but the timer of which we figured out how to force it to work but now we will be ordering the part from your great company.
Thanks for everything.
Carolyn Richrath

I had to call and reorder because I ordered the wrong part and the gal on the phone cancelled the first order and the right part came the next day!Amazing service!!!