MDB8949SAM0 Maytag Dishwasher - Instructions

Be sure to shut off power at circuit breaker and disconnect drain and water supply. Remove the dishwasher from the cabinet, lower it on its side. Remove three electrical connections from motor to various sensors. Remove three plastic wedges that secure the motor gasket to make a tight seal. The motor pops into the body of the dishwasher for removal. The replacement motor goes in just as you took it out. It took two people to set the motor right to ensure the good seal on the gasket for re-installation. Then turn it back upright and secure it in place. Couple suggestions, be sure to have ample towels around for leakage from water and drain lines. Be sure to cover the bottom of the dishwasher during disassembly and reassembly of the wash manifold. I dropped a screw in there and it took me some time to fish it out.
All in all, it went well. Don't pay a plumber for this job. I'm a clod and if I did it, you can.

disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.

removed rack
removed one screw
removed old seal
installed new seal
installed screw

Remove the mounting screws that hold the dishwasher under the counter top. Remove dust cover plates at the bottom of the machine. The machine will have to be pulled out, so turn off the water to the machine. Usually under the kitchen sink. Disconnect water supply and push it out of the way so the dishwasher can be pulled out. Pull machine out enough so you have access to the door cables and springs. The door will have to be in the closed(up) position to do the repair. Usually only one side is broken. Start with the broken side and copy the working side when installing new parts. Then repair the working side. To get the working side apart just pull on the spring and disconnect it from the cable. Do the reverse to reinstall.

All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,

First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!

Removed 2 screws that fasten dishwasher to underside of countertop. Pulled dishwasher out from under the countertop for access to sides. Hooked link on door, threaded cord around 2 wheels, hooked spring to back of dishwasher, stretched spring and hooked to eye on end of link cord. I found it very difficult to hook spring to link then try and stretch spring to hole at back of dishwasher. Easier to pull spring and link towards each other and connect. Note: This link was actually different from the original. The plastic end that connects to the door actually hits the first wheel when door is closed but it doesn't seem to prevent the door from locking properly (old design was better). However, I shaved this plastic end to provide better clearance.

thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.

Pulled dishwasher out from under the counter, removed faulty seal, installed new seal. Easy to understand directions are on web site.

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Replacement parts from factory installed using u tube support video


Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place

I did not get to repair my dishwasher using the part supplied by Partselect.com. I pulled my dishwasher out and found that the connector had fallen of the capacitor during installation. Happy to say that I returned the part for a full refund minus the shipping. Have bought from them before, and will again

Pulled off old seal found center of new seal and pushed new seal into channel that old seal came out of starting at top middle underneath the latch

I followed the video on the site and it worked perfectly!

watched video took less than 5 min to replace veeeery easy to do