MDB7749SAM1 Maytag Dishwasher - Instructions

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.

First I got online to troubleshoot issue to save mysel from a service call. One of the first UTube videos, a young man said usually the main issue was the lever. He pushed down on the floater. If it didn't click, than the lever below needed to be replaced. Most important to turn off the circuit breaker before beginning the repair. I got on whirlpool.com, Part Select, ordered the lever, which was under $10. And once delivered, was able to switch out the old lever with the new replacement. Part Quote video took me through the process step by step. The lever package was marked that usually it was only 2% of the time that replacing the lever fixed the issue. Of course, I was thrilled, my dishwasher was up and running again. Thank you.

Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.

Order both this seal and the seal for the bottom of the door at the same time.

With a little pressure, I was able to push off the broken wheel pieces with my thumbs. I was able to snap on the new wheel pieces really easily.
This job took less than 15 minutes to replace all 4 wheel pieces.

I opened the package took out the replacement part and installed it with no tools. Easy, done in 10 minutes.

Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!

Gently pull the old door seal out of it's track observing the orientation of the seal and the amount of extra seal at the ends of the seal grove/track..
Start installing the seal on one side leaving about the same amount of extra seal as original seal before removal.
Be sure the seals orientation is the same as the seal that was removed.
Carefully pressing the seal into the grove/track designed to hold the seal. Be careful to fully seat the seal into the grove/track.
The corners will be a little tricky, but carefully press and seat the new door seal all the way around. There should be a little extra seal after you get to the end of the grove/track.
Good luck, the new door seal solved my water leak.

Soak up the water in the dishwasher with an old towel. Removed the cover under the dishwasher. Found the pump and twisted it off anti clockwise. Replaced with the new pump. Run a quick cycle, to make sure it pumped out all the water. My wife has used it several times since without any issues.

I Removed the upper wash rack by removing locks on each front slide of rack. I laid a towel in the bottom of the washer to keep anything dropped, retrievable. I then removed the top screw closest to the spinner location. I then carefully pulled down on the mounting, which exposed the bad bushing lock. I removed the old bushing lock and replaced with new one. I then replaced the spinner with a push with one hand while holding the bushing in place with the other hand. You will feel a snap as all goes into place. Make sure new spinner spins freely. Now reinstall removed screw. Do not over tighten. Now reinstall lower rack, carefully aligning water feed in rear of washer, and making sure all rollers are back in sliding rack. Reinstall locking tabs onto sliding rack. Now slide out rack, it should not come off slider. Important: now remove the towel in the bottom of the washer. If left in place, you will have a fire during the drying cycle. Close the door and test your washer through a cycle. I felt confident and did a load of dishes. If all went well, spinner should be in place, not in the bottom of the washer.

simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.

First I would like to say I was concerned about undertaking a dishwasher repair ,as I now am legally blind and I was concerned that my vision impairment might cause me a problem. My dishwasher pump motor was not running and from the humming sound I could tell it was cycling power off on the thermo switch overload. The pump can be removed by turning it counter clockwise,however it would not move and I could not rotate the motor manually, IT appeared that the impeller must be jammed,so I removed the complete ascribe..After I removed it the motor still could not be removed for replacement. I ordered the complete assembly from PartSelect.com an was supervised how fast it was delivered. The hardest part was getting the seal to go in place as it was new and a tight fit. The Partsselect.com video's ,on repair instructions were very helpful. I reinstalled the dishwasher and everything worked fine.Thanks for thefast delivery of my order.

I had to remove the baskets, spray assemblies (no tools needed) and disassemble the section of the pump that contained the chopper assembly. (removing three Torx screws)
I had to remove a part of the old chopper that had gone into the pump, but I was lucky that a magnet grabbed it so I didn't have to disassemble the pump.
The total repair was not difficult. The only problem was access (hands in the way while repairing difficult to see) and compressing the spring on the new chopper while trying to slip it into the groove.
The parts came in three days and they fit perfectly

After looking at what everyone else had done, I decide that I would take the dishwasher out of the wall space and set it on its side. This require me to turn off the power first. Then I pull the diswasher out from its space in the wall. I turned off the the water and then took off the water hose, then took of the return hose. There was water left in both, so there was a little water on the floor as a result of this. Then I finally pulled out the unit and laid it down on its side. The motor was very visible and was easy to access. The hardest part was finding the bolt to take it off. I pulled off the power connector to the motor and then took off the one bolt that was holding the motor on the washer. Then I twisted the motor, but it would not come off. I finally got a screw driver and put it in the small opening between the motor and the connection and it finally came off. This took all of about 30 minutes. Once I got the motor off, I notice that the aluminum grating inside was dirty and needed cleaning. So I cleaned this and put it back inside. The new motor came with every thing, so I put it in and twisted it. Then put back in the bolt, reconnected the power cable, put back on the water and reconnected the output cable. In order to make sure there were no leaks before I put it back in for good, I ran a short wash to check to see if everything was tight. There were no leaks, so I put everything back in the wall. It really did sound very nice now. This dishwasher unit came with noise padding, so I put that back as well. The dishwasher, now is very quite and I don't mind it running any time during the day. The hardest part about this is getting the motor off and find the bolt. It is down between motor and the unit and there was some aluminum between this and the dishwasher, so you need a long nutdriver to get it off.

My wife hired a local repairman when the right side spring cable broke (I was out of town). He took two hours to fix it (and two appointments). The door would then pop open when running. He came back and replaced the latch. Problems persisted. I then ordered new hinges and replaced both in half hour or so. Would recommend doing all of these repairs yourself. None of these repairs are that hard and definitely not worth paying hundreds to do it. Trickiest part is pulling the dishwasher out from the counter without impacting the electrical or water connections. Disconnecting the power is important on all repairs. When you take the screws out of the door to get to the hinges, make sure you have a helper just to hold the door up while removing the last few screws. The left side hinge was really bent (when the right side spring cable broke) - caused the door to be out of square and thus would not effectively close. This was obvious after a 5 minute search on this this and other repair sites. Process that I used: 1. remove screws from both sides holding dishwasher into counter (may have screws into countertop as well). 2. turn off power, 3. pull out dishwasher far enough to see hinges and springs (careful of connections), 4. remove front door screws, 5. take off front panel, 6. remove spring cables (pull cable taut and remove "hook" from hinge)., 7. unscrew two screws holding hinge to door, 8. bend metal fingers around hinge pin to be able to remove hinge., 9. attach hinge in opposite path. 10. repeat on other side (if necessary), 11. reconnect things in opposite order...test door prior to reattaching door panel. Make sure you level the unit with the adjustable feet. Make sure screws in sides of cabinet aren't too tight as it can take the unit out of square pretty easily...